The first start of a new installation is where most of the time goes, and most first-start problems are simple: a sensor reading upside down, a trigger offset 360° out, an injector on the wrong output. Working through the checks in the right order, before you ever crank the engine, turns a frustrating day into a short one. This page is that order: each step says what to check, why, and which page explains it in detail.
Have a fire extinguisher at hand, the car on stands or the wheels chocked, and someone ready to switch the ignition off. Check for fuel leaks before every first start.
- Wiring. Check the ECU's power, grounds and the main relay against the wiring diagram or your plug-in adapter's pinout. Poor grounds cause more strange faults than anything else.
- RM-Tuner. Install RM-Tuner and the USB drivers.
- A base map. Start from the base map closest to your engine, never from an empty tune.
Switch the ignition on, connect RM-Tuner, and save a copy of the ECU's tune before changing anything.
- Firmware. Update to the latest firmware if RM-Tuner offers one: Firmware update.
- Engine configuration. Cylinders, firing order, ignition mode and outputs, injectors: Engine configuration.
- Sensors. Every reading must make sense with the engine cold and stopped:
| Reading |
What it should show |
| Coolant and air temperature |
The air temperature in the workshop, both about the same on a cold engine. See Coolant and air temperature sensors |
| MAP |
The atmosphere: about 100 kPa at sea level. See MAP sensor |
| TPS / pedal |
0 % closed, 100 % fully open, smooth in between. See TPS calibration |
| Battery voltage |
12–13 V with the engine off |
| Wideband |
Warming up, then reading air (very lean) with the engine off. See Wideband sensor |
- Status. Open Diag → Status: no sensor you use should read Failure. See Diagnostics.
- Outputs. With the fuel pump fused out or the rail empty, use Hardware test to click each injector and fire each coil, and check each one is the cylinder you expect. Check the fuel pump primes at key-on: Fuel pump.
¶ 3) Fuel and trigger settings
- Fuelling. Set the fuel algorithm, the required fuel for your engine and injectors, and the injector dead time: Fuelling settings, Injector dead time.
- Trigger. Set the crank wheel, the cam and the inputs: Crank and cam sensors, Trigger inputs.
- Cranking and warm-up fuel. Check the cranking and after-start enrichment suit the coolant temperature: Cold start and warm-up.
- Idle. A sensible Target position for the coolant temperature, with Closed loop off for now: Idle control.
With the fuel pump disabled (or the injectors unplugged), crank the engine for a few seconds and watch:
- Engine speed. RM-Tuner should show a steady cranking speed, typically 150–300 rpm.
- Trigger. Open Scope → Trigger analyzer: Trigger decode OK, the right number of teeth and sync held. See Trigger analyzer.
- Timing. With a timing light on cylinder 1 and Fixed advance set, the timing mark must match the fixed advance. Adjust the trigger offset until it does: see Ignition table.
A timing light reading exactly 360° out, or a misfire that will not start at all, usually means the cam phase or the trigger offset is a full turn out.
- Re-enable the fuel pump, prime it with a few key-on cycles and check for leaks again.
- Crank. Most engines on a sensible base map start within a few seconds. If it fires but will not run, adjust the cranking enrichment; if it does not fire at all, go back to the trigger and the timing.
- Once it runs, check the timing again with the light at idle, with Fixed advance on.
- Watch the coolant temperature, the oil pressure and the wideband. Let it warm up gently, adjusting the idle Target position and the warm-up enrichment as it goes.
- Store the tune and save a copy.
- Wideband and closed loop: check the wideband reads sensibly, then switch on the fuel closed loop.
- Idle: tune the Target position through the warm-up, then switch on idle Closed loop: Idle control.
- Fuel table: tune the idle and light-load cells, then let the adaptation refine them while you drive.
- Safety: set the rev limiter, knock control and, on a boosted engine, lean and overboost protection before any full-load running.
- Logging: set the SD card to log every drive: Datalogging.
- Full load: tune the fuel table, the ignition table and the lambda targets at full load, preferably on a dyno.
In order: Status for sensor failures, the trigger in the Trigger analyzer (decode OK, sync held), the timing with a timing light while cranking, the fuel pump priming, and the injector and coil outputs with Hardware test.
Yes, if the base map matches your engine closely (cylinders, injectors, sensors). Check the required fuel and the injector dead time for your injectors before the first start.
¶ Do I need a wideband for the first start?
No, but you need it as soon as the engine runs: fuel tuning without a wideband is guesswork.
Contact customer support at [email protected].
Related pages: Getting started · Engine configuration · Trigger analyzer · Diagnostics · Fuelling settings