The mixture in the cylinder does not burn in an instant: from the spark, the flame takes a couple of milliseconds to spread across the chamber. To get the most push on the piston, the pressure should peak just after top dead centre (TDC), so the spark has to fire before it, while the piston is still rising. How many degrees of crankshaft rotation before TDC it fires is the ignition advance, and the ignition table sets it for every engine speed and load.
The RM-Primis ECU takes the advance from this table, then adds its corrections (coolant and air temperature, knock control, idle control, launch and shift cuts) to give the advance it actually fires at. This page explains what the right advance is, how to check the base timing, and how to tune the table safely.
How much advance an engine wants depends on how fast the mixture burns and how much time there is:
| Condition | Advance | Why |
|---|---|---|
| Higher engine speed | More | Less time per degree, so the spark must fire earlier |
| Light load (low MAP) | More | A thin charge burns slowly |
| High load and boost | Less | A dense charge burns fast and knocks easily |
| Hot air, low octane, lean mixture | Less | All make knock more likely |
That is why a typical ignition table has the most advance at high revs and light load, and the least at low revs and full load.
Open Tune → Ignition → Ignition table.
| Across (RPM) | Engine speed |
| Down (Load) | Engine load, on the same axis as the fuel table unless the table has its own (see Table axes) |
| Values | Ignition advance in degrees before TDC |
The table tools, the 3D view and Follow engine are described on the Fuel table page. Table: Primary / Secondary chooses which of the two ignition tables you are editing; which one runs is set on Table switch.
Before you tune a single cell, make sure the ECU's idea of where the crankshaft is matches the engine. If it is 5° out, every number in the table is 5° out. Fixed advance locks the ignition at Fixed advance angle, whatever the table says, so you can check it with a timing light.
Never drive with Fixed advance on: the engine gets the same advance at every speed and load, which is far too little at high speed and can be too much under load.
Start safe. Begin from a base map for a similar engine, with a little less advance than you expect it to want, especially at full load and under boost. A few degrees too little costs some power; a few degrees too much can cost an engine.
On a dyno: find the best torque. At each engine speed and load, hold the engine steady and add advance a degree or two at a time while the torque rises. Stop as soon as it stops rising, or at the first sign of knock, whichever comes first, and take a degree or two back as a margin. That is the cell's value. Work through the table this way, part load first, full load last.
On the road: work conservatively. Without a dyno you cannot see the best torque, so stay a few degrees under the knock limit at full load, and use the part-load areas to improve response and economy: an engine that feels sluggish and runs hot at cruise usually wants more advance there.
Listen for knock. Use the knock control, and listen with det cans if you have them, while you tune full load. Hot air, a lean mixture or a tank of poorer fuel all bring the knock limit closer, so leave a margin for the worst day the car will see.
Keep it smooth. Use Interpolate between the cells you tuned and check the 3D view: the engine passes through every cell between them, and a step in the table is a jolt in the torque.
High octane fuel, low air temperature and rich mixtures allow more advance; boost, hot air and lean mixtures need less. Tune for the worst conditions the car will see.
The advance in the table is the starting point. The ECU then corrects it for:
| Correction | Where |
|---|---|
| Coolant and air temperature | CLT and IAT ignition corrections |
| Secondary table | Table switch |
| Knock | Knock control, under Safety in RM-Tuner |
| Idle speed | Idle control's ignition control, under Tune → Idle control |
| Launch, flat shift and gear shift cuts | Tune → Motorsport |
The Ignition advance reading at the bottom of RM-Tuner shows the advance the ECU is firing at, with every correction included: compare it with the table to see what the corrections are doing.
A rotary engine fires two plugs per rotor: the leading plug, timed by the ignition table, and the trailing plug a few degrees later. The Rotary trailing offset table (Tune → Ignition → Rotary trailing offset, shown when the engine is set up as a rotary) holds that split, in degrees after the leading spark, by engine speed and load.
A split of about 10–15° at light load helps the burn and the idle; at full load and high boost most tuners close it down towards 0–5°, so the trailing spark adds less heat at the end of the burn. Tune it with the same care as the ignition table, watching the knock and the exhaust temperature.
The angle, in degrees of crankshaft rotation before top dead centre, at which the spark plug fires. The mixture takes time to burn, so it is lit early enough for the pressure to peak just after TDC.
Knock: a metallic rattle or pinging under load, and knock readings in the knock control. Back the advance off in that area straight away. On a dyno, too much advance also shows as torque that stops rising or falls as you add advance.
Check it with Fixed advance on, at a steady idle, and correct First tooth angle on the crank sensor page (see Crank and cam sensors).
Contact customer support at [email protected].
Related pages: CLT and IAT ignition corrections · Ignition coil dwell · Crank and cam sensors · Table axes · Torque tables