The large maps of the RM-Primis ECU (fuel, ignition, lambda, intake VVT and exhaust VVT) share their RPM and load axes: change an axis point once and every map follows. The Axis sources page sets how many points those axes have, what the load axis measures, and whether a secondary table uses the main axes or a second, alternative set.
Open Setup → Engine → Axis sources.
| Setting | What it does |
|---|---|
| Number of RPM sites | How many engine speed points the large maps have across, up to 24 |
| Number of Load sites | How many load points they have down, up to 24 |
| Import | Reads the shared axes from another tune file |
More sites give finer control where the engine needs it, such as around idle or where boost builds. The axis values themselves are edited on any of the maps, by typing into the axis cells; every map that shares them follows. The site counts can also be changed from the Axis sites section of a table's information panel (see Fuel table).
Changing the number of sites or the axis values moves where every map's cells sit. Check your fuel and ignition tables afterwards.
The ECU interpolates between axis points: at 2750 rpm, between the 2500 and 3000 columns. So the table can only follow the engine as closely as its points allow. Put the points where the engine needs them:
An example for a turbocharged engine idling at 900 rpm and revving to 7000 rpm with 1.0 bar of boost: RPM points at 500, 800, 1000, 1250, 1500, 2000, 2500, 3000, 3500, 4000, 4500, 5000, 5500, 6000, 6500, 7200; load points from 20 kPa to 220 kPa, closer between 30 and 100 kPa where the engine cruises.
Set the axes before you tune the tables: moving them later moves every cell's meaning.
What the load axis of each table measures. Shared load follows the fuel algorithm: manifold pressure (MAP) with speed density, throttle position with Alpha-N. The fuel tables can also use another source:
| Source | Use it for |
|---|---|
| MAP, TPS, Pedal | Load by manifold pressure, throttle or pedal position, whatever the fuel algorithm |
| TPS change/s, MAP change/s | How fast the throttle or the pressure is moving |
| CLT, IAT, Ethanol, Fuel temp | Temperatures, or the ethanol content from a flex fuel sensor |
| Vehicle speed | Road speed |
| GP Analog 1–4 | One of the general purpose analog inputs |
| Intake VVT angle, Exhaust VVT angle | The measured cam angles |
The secondary tables (see Table switch) can use a different axis set:
| Setting | What it does |
|---|---|
| Secondary shared axes (Fuel, Lambda, Ignition, Intake VVT, Exhaust VVT) | Main: the secondary table uses the same axes as the first. Alternative: it uses the alternative axes |
| Alternative load source | What the alternative axes' load measures, from the same list as above |
For example, a secondary fuel and ignition map for ethanol can use Ethanol as its load, or a secondary fuel table can use MAP while the main maps run Alpha-N.
The engine rarely sits exactly on an axis point. At 2750 rpm and 55 kPa, between the 2500 and 3000 rpm columns and the 50 and 60 kPa rows, the ECU takes the four cells around it and blends them by how close it is to each: halfway between 2500 and 3000, and halfway between 50 and 60, each of the four cells counts for a quarter. This is interpolation, and it is why a table with 16 points by 16 can describe a smooth engine.
It has two consequences for tuning:
A worked example. A 2.0 litre turbo engine spools between 3000 and 4000 rpm and spends little time above 6500 rpm. A good RPM axis puts points every 250–500 rpm from 2500 to 4500, every 500 rpm above, and only a couple of points below 1500 where the engine only idles. The load axis puts several points between 20 and 60 kPa for cruise and idle, a point at 100 kPa (atmospheric), and the rest spread up to the highest boost.
Changing an axis does not move the values in the tables: each cell stays the number it was, but it now stands for a different speed or load. Change the axes before you tune the tables, not after.
Up to 24 RPM sites and 24 load sites on the large maps, set on Axis sources and shared by all of them.
Yes: set Secondary shared axes → Fuel to Alternative, and choose the Alternative load source.
Contact customer support at [email protected].
Related pages: Fuel table (VE) · Table switch · Fuelling settings · Ignition table