The RM-Primis ECU has two of each main table: fuel, lambda, ignition, intake VVT, exhaust VVT and boost. The table switch decides how the second (secondary) table is used: instead of the first, added to it, as a percentage of it, or blended with it, and what turns it on: a switch on the dashboard, a CAN signal, the gearbox's sport mode, or a value such as boost pressure.
Typical uses:
Open Tune → Fuel → Table switch. Each table has a card of its own.
The header of each card says what the ECU is running now: Running table 1, Running table 2 or Running both tables.
| Usage method | What happens while it is active |
|---|---|
| Off | The ECU runs the first table alone |
| Switch to table 2 | The ECU runs the second table instead of the first |
| Add values | The second table's value is added to the first's. A secondary ignition table of 5.0 everywhere adds 5° |
| Percentage | The second table scales the first; 100 % means no change |
| Blend | The ECU fades from the first table to the second as the blend value rises to its Max |
While the activation is off, the ECU always runs the first table alone.
Once a usage method is chosen, Activation appears, and then the setting it needs:
| Activation | What turns the second table on | Then choose |
|---|---|---|
| Always | All the time (for Add values, Percentage and Blend) | Nothing else |
| Input | One of the ECU's inputs, such as a switch on an analog input. On while the input is high; tick Inverted for on while it is low | The input |
| CAN bus | A CAN input, or the gearbox's sport mode | CAN input, or the sport mode |
| Above threshold | A value the ECU reads rising above the Threshold | The value: MAP, TPS, Pedal, RPM, TPS/s, MAP/s or Ethanol, and the threshold |
For CAN input, set up the CAN variable that switches this table in RM-Tuner under Setup → CAN bus → Input settings: a bitfield variable's bit, with its control set to switch this table.
With a gearbox that has sport modes (the BMW 8HP, the E46 SMG, the E36/E46 automatic), the sport modes are offered under CAN bus: the table then switches only while the gearbox is in that mode, and stays on its first table outside it.
Each card's STATUS labels show what the ECU is doing with that table now, ON or OFF:
| Label | Meaning |
|---|---|
| Table 2 only | Running the second table alone |
| Both | Using both tables (Add values, Percentage or Blend) |
| Input | The input that switches it is on |
| CAN input | The CAN signal that switches it is on |
| VTEC | Switched by the VTEC output |
Use them to check a switch works before you drive: press your switch and watch Input and the card's header change.
The order is always the same: build the second table, choose how it is used, choose what turns it on, and check it works before you drive.
You run pump fuel on the road and a higher-octane race fuel at the track, where the engine can take more ignition advance and a slightly different mixture.
On a car with a gearbox sport mode (BMW 8HP, E46 SMG, E36/E46 automatic), you want a few degrees more advance only in Sport.
Add values and Percentage are often easier to tune than a whole second table: the secondary table only holds the difference, so when you retune the primary table, the difference still applies.
When you switch the fuel table for a different fuel, switch the lambda table and, usually, the ignition table with it. And tune a secondary table as carefully as the primary: the engine will run on it at full load.
Yes. On the ignition card choose Add values, activation CAN bus and the sport mode, and put the extra advance in the secondary ignition table. Outside sport mode the ECU runs the first table alone.
Yes. The secondary tables can use their own load axis, set on Table axis.
Contact customer support at [email protected].
Related pages: Fuel table (VE) · Lambda / AFR target table · Ignition table · Table axis · CAN bus