The fuel table is the heart of the RM-Primis ECU's fuelling. It describes how well your engine breathes: for every engine speed and load, how full each cylinder gets with air, as a percentage. That figure is the engine's volumetric efficiency (VE). The ECU multiplies the required fuel by the VE of the cell the engine is running in, then applies the load, the mixture target and its corrections, to get every injection.
Because the table describes the engine and not the injectors, it has a real meaning you can reason about. This page explains what the numbers mean, how to read and edit the table, and how to tune it from a first start to a finished map. The table tools described here are the same on every table in RM-Tuner.
An engine is an air pump. At each engine speed and throttle opening, the intake and exhaust let a certain amount of air into each cylinder: the VE. A cell of 100 % means the cylinder fills as completely as the manifold pressure allows; 60 % means it only gets 60 % of that.
With speed density, the ECU also multiplies by the manifold pressure. So boost does not need huge numbers: a turbo engine at 200 kPa still sits around 100 % VE, and the doubled pressure doubles the fuel by itself.
Because the fuel follows the VE directly, a cell that is 5 % too low makes the engine 5 % lean there. That makes the table easy to correct: measure how far off the mixture is, and change the cell by the same percentage.
With Incorporate in fuel math on the Lambda table, the ECU also builds your mixture target into the fuel. Then a well-tuned fuel table means you change the mixture by changing only the target, and leave the fuel table alone.
Open Tune → Fuel → Fuel table.
| Across (RPM) | Engine speed |
| Down (load) | Manifold pressure in kPa with speed density, throttle position with Alpha-N, or the load source chosen on Table axes |
| Values | Volumetric efficiency in %, from 0 to 1600 %, in steps of 0.024 % |
Table: Primary / Secondary at the top right chooses which of the two fuel tables you are editing. The ECU can run either, switched by a switch, a CAN signal or a drive mode, as set on Table switch.
Everything in this section works the same on every table in RM-Tuner.
Click a cell and type a value, or drag across several cells to select them and change them together. Connected to the ECU, a change takes effect straight away, so you can tune with the engine running and hear and see the result. Cells changed but not yet stored in the ECU's memory are marked; Store all at the top of the window stores everything, and with Auto-store on RM-Tuner does it for you.
| Tool | What it does | Key |
|---|---|---|
| Selection tools... | Arithmetic on the selection, filling in a direction, and applying reference values | |
| Smooth | Averages each selected cell with its neighbours | Ctrl+S |
| Interpolate | Fills the selection evenly between its corner values | Ctrl+I |
| -10 / -1 / +1 / +10 | Subtracts or adds that amount to every selected cell | Ctrl+- / - / + / Ctrl++ |
| -5% / -1% / +1% / +5% | Takes off or adds that percentage of each selected cell's value | / and * for 5 % |
| Undo / Redo | Puts the last change back, or does it again | Ctrl+Z |
| Copy / Paste | Copies the selected cells and pastes them elsewhere | Ctrl+C / Ctrl+V |
The percentage buttons are the ones you will use most on a fuel table: if a group of cells reads 4 % lean, select them and press +1% four times.
| Option | What it shows |
|---|---|
| 2D | The numbers |
| 3D | The table as a surface; drag it to turn it. Bumps and holes that are not real show up at once |
| Graph | A curve as a line, or on a map the slice through the selected cell |
| Follow engine | Keeps a cyan marker on the cell the engine is running in, so you always know which cell you are tuning |
| Heat | Relative colours each cell against the table's own spread; Absolute keeps the colours fixed to the values |
On a wide enough window, the panel at the right shows:
| Section | What it is for |
|---|---|
| What is this table? | A short description of the table |
| Selected cell / Operating point | The cell you are on, and the cell the engine is running in |
| Table set | Primary or secondary |
| Import / Export: From a tune file... | Reads this table out of another tune file and fits it onto your axes |
| Selection: Calculated / Not calculated | Marks cells as already tuned, for the fuel analyser |
| Fuel analyser: Build from a log... | Reads a datalog and turns the mixture error it recorded into a correction for this table |
| Axis sites | How many RPM and load points the large maps have (2 to 24), shared by all of them |
| Cell marks | The colours for the cell the engine is running in and for cells changed but not yet stored |
You need a wideband sensor you trust, a warm engine, and the Fuelling settings and injector dead time already right.
First start. Begin from a base map for a similar engine, or from a smooth table that rises from about 45 % at idle to 85–95 % at full load. The first job is only to get the engine to idle cleanly. Switch the closed loop off, and the temperature and acceleration compensations too if you want to see the table alone (Compensation disable on Fuelling settings).
Idle. With Follow engine on, watch the cyan marker: it shows the cell, or the four cells between which the engine sits. Compare the measured mixture with the target. If the engine runs at 15.4 AFR and you asked for 14.7, it is 15.4 ÷ 14.7 = 1.048, about 5 % lean: raise those cells by 5 %. Lean idles hunt and stumble; rich idles smell of fuel and soot the plugs.
Light load and cruise. Drive steadily, or hold steady loads on a dyno, and work through the cells you pass through: a few hundred rpm and a few kPa at a time. These are the cells the car spends most of its life in, so they matter most for driveability and economy.
Higher load. Work upwards in load and speed in small steps, watching the mixture and listening for knock. Keep the full-load mixture on the safe, rich side of your target until the whole area is tuned.
Fill in and smooth. You will never visit every cell. Use Interpolate between the cells you have tuned, and Smooth away steps: the engine moves through every cell, and a sudden step in the table is a sudden step in the fuelling. The 3D view shows whether the table makes a smooth, sensible shape.
Let the ECU help. Once the table is close, switch on the closed loop and adaptation: the ECU then learns the remaining errors while you drive, cell by cell, and you apply them to the table. Or record a datalog and use Build from a log... to turn the errors it recorded into a correction.
Never tune high load with a wideband sensor you are not sure of, and never lean a full-load area out until the engine is fully tuned. A few percent rich costs a little power; a few percent lean under boost can cost an engine.
A finished fuel table tells you about your engine. A hump in the middle of the rev range is where the intake and exhaust resonate and the engine makes its peak torque. A fall at the top is where it runs out of breath. A sharp hole or spike that the neighbouring cells do not share is almost always a tuning error, not the engine: check it again.
A table of volumetric efficiency: how completely each cylinder fills with air at each engine speed and load, in %. The ECU works out the fuel from it, so the VE table is the engine's fuel map.
Some engines fill better than their capacity at peak torque, thanks to tuned intake and exhaust, and the table also takes up any error in the required fuel or injector data. Values a little over 100 % are normal; values far over it usually mean the injector flow or required fuel is wrong.
Work out how far off it is as a percentage (measured AFR ÷ target AFR), select the cells and change them by that percentage with the +1% and -1% buttons.
Yes: From a tune file... in the Table information panel reads the table out of another tune and fits it onto your table's axes. Check it against your engine before you drive.
Contact customer support at [email protected].
Related pages: Fuelling settings · Lambda / AFR target table · Adaptation table · Table axes · Table switch