The RM-Primis ECU knows where the engine is in its cycle from the crank sensor, which reads a toothed wheel on the crankshaft, and the cam sensors, which tell it which half of the 720° cycle it is in. Everything the ECU does is timed from them. The Crank sensor page tells the ECU what wheels and patterns your engine has, and where the first tooth is relative to top dead centre (TDC).
Take a common 60-2 crank wheel: 60 evenly spaced teeth, two of them missing. As the wheel turns, the sensor sees a tooth every 6°, then a gap. The gap is the reference: when the ECU sees it, it knows exactly where the crankshaft is, and from then on it counts teeth to follow every degree.
But the crankshaft turns twice per engine cycle, and the gap looks the same on both turns: from the crank alone, the ECU cannot tell whether cylinder 1 is on its compression stroke or its exhaust stroke. The cam turns once per cycle, so a cam sensor answers that: a single tooth, or a half-moon wheel that is high for half a turn, tells the ECU which turn it is on. With both, the ECU is synchronised: it can fire each spark and time each injection for its own cylinder.
Two things therefore have to be right:
Open Setup → Engine → Crank sensor. Which input each sensor is wired to, and its edge, is set on Trigger inputs.
| Setting | What it is |
|---|---|
| Crank Ref | Switch on to use the crank sensor as the ECU's main position reference |
| Trigger pattern | The pattern the ECU decodes, such as Multi tooth for a missing-tooth wheel. For a distributor, choose missing tooth and set the reference teeth to 0 |
| First tooth angle | The crank angle before TDC of cylinder 1 when the reference tooth passes the sensor. This is your trigger offset: check it with a timing light (below) |
| Relative to TDC | How First tooth angle is entered. Off: degrees before TDC, as other brands state it (no negative values). On: an offset of up to half a turn either side |
| Teeth/cycle | The teeth the wheel would have over a full 720° cycle, counting the missing ones. A 60-2 wheel on the crank: 120. A 24-tooth wheel in a distributor, turning at cam speed: 24 |
| Reference teeth | The teeth missing (negative) or added (positive) at the gap: -2 for a 60-2 wheel, -1 for a 36-1, +1 for a wheel with one wider tooth |
| Number of Teeth | The teeth physically on the wheel: 58 on a 60-2, 35 on a 36-1 |
The number in brackets beside Teeth/cycle and Number of Teeth is what the ECU is actually counting. If it differs from what you entered, the pattern, the wheel or the sensor's edge is wrong.
Check opens the trigger offset analyser: with the engine cranking or running, it shows the trigger signals the ECU sees and offers offsets to choose from.
Each cam input (CAM 1 and CAM 2) has:
| Setting | What it is |
|---|---|
| CAM1 ref. / CAM2 ref. | Switch on to use that cam sensor for synchronisation |
| Trigger pattern | The cam wheel's pattern, such as Single 180° (a half-moon wheel, high for half a turn) |
| Sync reference | Which edge of the pattern the ECU takes as the reference for cylinder 1, before or after TDC |
| Number of Teeth / Reference teeth | For multi-tooth cam wheels; with the number the ECU counts in brackets |
| Cam angle | The live angle of the cam signal. On engines with variable cam timing it moves with the VVT; see Intake and exhaust VVT |
| Number of cycles | A live count of engine cycles: it keeps rising while the engine runs and the ECU stays synchronised |
| Lock ignition | Fixes the ignition at the angle beside it, for checking the timing. It is the same switch as Fixed advance on the Ignition table |
The drawing at the bottom shows your crank wheel and cam wheels as configured, and the whole 720° cycle: the crank teeth, the gap where the crank sensor finds its reference, and each cam signal with its sync edge. Use it to check the settings match the wheels on your engine.
Never drive with Lock ignition on.
Missing-tooth crank wheels (such as 60-2 and 36-1), wheels with an extra or wider tooth, multi-tooth cam wheels, half-moon cam wheels and distributor triggers, with up to two cam sensors. Choose them under Trigger pattern.
The ECU is not seeing the wheel you described. Check the Trigger pattern, Number of Teeth and Reference teeth, the sensor's wiring, and the input's Edge on Trigger inputs.
Contact customer support at [email protected].
Related pages: Trigger inputs · Engine configuration · Ignition table · Intake and exhaust VVT