The RM-Primis ECU has five inputs for speed and position signals: a Crank VR and a Cam VR input for magnetic (variable reluctance) sensors, a Hall input, and two universal Trigger inputs. Each can be given a job (crank reference, cam 1, cam 2, clutch, or a wheel speed sensor) and the signal edge it reads. The same page sets the cranking speed and calibrates the wheel speed sensors, and the VR threshold page sets how the VR inputs tell a real tooth from noise.
There are two kinds of speed and position sensor, and they need different inputs:
If you are not sure which you have: two wires and no supply is almost always VR; three wires with a 5 V or 12 V supply is Hall.
Open Setup → Sensors → Trigger inputs, and Setup → Sensors → VR threshold for the VR threshold table. What the crank and cam wheels look like is set on Crank and cam sensors.
| Input | Sensor type | Notes |
|---|---|---|
| Crank VR | Magnetic (VR) | With its own threshold table (below). Usually the crank sensor |
| Cam VR | Magnetic (VR) | Automatic threshold. Plot opens a live graph of the signal |
| Hall input | Digital (Hall) | No pull-up of its own: an open-collector sensor needs an external 1 kΩ pull-up resistor |
| Trigger input 1 / Trigger input 2 | Digital (Hall or square wave) | With a Pull Up switch for open-collector Hall sensors |
For each input:
| Setting | What it does |
|---|---|
| Input | Its job: Disabled, Crank Ref, CAM 1, CAM 2, Clutch, Traction Speed sensor (driven wheels) or Untrac. Speed sensor (non-driven wheels) |
| Edge | Rising or Falling: which edge of the signal the ECU reads. The wrong edge moves the timing and can stop the engine from synchronising |
| Pull Up | On the trigger inputs: switch on for Hall and open-collector sensors that need one |
| Multiplexed | On some inputs: read a sensor that sends more than one value on one wire, such as an Ethanol % sensor or a Hella OPS+T oil pressure and temperature sensor |
Choose the edge with the Plot tool: it shows the real signal, so you can see which edge is clean and consistent. Video: the trigger plotter and trigger edges
Maximum cranking is the engine speed below which the ECU treats the engine as cranking, and uses its cranking fuel and timing (see Cold start and cranking enrichment). 300–400 rpm suits most engines: above the fastest the starter turns it, below the slowest idle.
Speed sensors calibrates the driven (Tractioned wheels) and non-driven (Untractioned wheels) speed sensors, used for traction control, launch control and road speed:
| Setting | What it does |
|---|---|
| Speed with KM/H or MPH | The speed you will drive at while the ECU learns |
| Pulses per meter | How many pulses each sensor gives per metre travelled |
| Learn | Drive steadily at the Speed you entered and press Learn: the ECU measures Pulses per meter |
If you know the figure (teeth on the wheel ring divided by the wheel circumference in metres), type it in instead. A Learn button is greyed out until an input is set to that speed sensor.
A VR sensor makes an alternating voltage that grows with engine speed: small while cranking, several volts at high speed. The ECU only counts a tooth once the signal has passed the threshold voltage, which comes from this curve by engine speed.
| Threshold | Result |
|---|---|
| Too high at low speed | Teeth are missed while cranking: no rpm reading, the engine will not start |
| Too low at high speed | Electrical noise is counted as teeth: lost sync or misfires at high rpm |
The live values show the RPM and the sensor's Voltage now: the threshold should sit well below the voltage at every engine speed, but well above the noise. Quick cal, in the settings under the curve, draws a starting curve.
Check the crank input's Input is Crank Ref on the input the sensor is wired to, then its Edge. With a VR sensor, lower the VR threshold at 300–500 rpm.
With a VR sensor, raise the threshold at high engine speed. Check the sensor wiring is shielded and its screen is grounded at one end only.
Contact customer support at [email protected].
Related pages: Crank and cam sensors · Engine configuration · Flex fuel sensor · Wiring diagram