Automatic and automated gearboxes (ZF 8HP, ZF 5HP, BMW SMG, DSG and others) work with engine torque. The gearbox controller needs to know how much torque the engine makes at every moment to set its clutch pressures and shift smoothly, and during a shift it asks the engine to reduce torque for a moment, or to raise the revs for a downshift. The RM-Primis ECU does all of this from the Torque tables page.
| Table | What it does |
|---|---|
| Engine torque | The torque the engine makes, by engine speed and load, sent to the gearbox |
| Ignition torque reduction | How much torque each degree of ignition retard removes, by engine speed |
| Throttle rev match | The throttle opening for a downshift blip, by the engine speed to reach |
These tables matter for every automatic gearbox integration. With unrealistic torque values, the gearbox shifts harshly or late, slips, or flares on shifts.
All the time, the ECU tells the gearbox controller how much torque the engine is making, from the Engine torque table. The gearbox uses it to set its clutch pressures: enough to hold the torque without slipping, no more, so the shifts stay smooth. If the table says 200 Nm and the engine really makes 300, the clutches slip and wear; if it says 400, the shifts bang.
On an upshift, the gearbox has to slow the engine down to the next gear's speed while one clutch lets go and the next takes up. To do that smoothly and quickly, it asks the ECU to reduce torque for a fraction of a second. The ECU retards the ignition (and, depending on the Torque intervention method, cuts sparks or fuel), using the Ignition torque reduction curve to work out how much retard gives the reduction asked for.
On a downshift, the engine has to speed up to the lower gear's speed. With an electronic throttle, the ECU blips the throttle open to the value in the Throttle rev match curve, so the engine meets the next gear at the right speed, as a driver heel-and-toeing would.
Get the three tables right and the gearbox behaves as it did with its original engine controller.
Open Tune → Motorsport → Torque tables. The three tables are on tabs, and the settings are in Torque tables settings under them. The table tools are described on the Fuel table page.
The engine's torque in Nm, by engine speed (across) and manifold pressure (down). The ECU reads it live and sends it to the gearbox controller, exactly as the original engine controller would.
Fill it with your engine's real torque:
Keep it smooth and realistic: the gearbox believes it. If the car shifts harshly, the table probably says less torque than the engine really makes; if shifts flare or slip, it says more.
When the gearbox asks for less torque, the ECU works out how much ignition retard gives that reduction from this curve: the torque removed for each degree of retard, by engine speed. A value of 16 at 3000 rpm means each degree of retard takes 16 Nm off.
On a downshift the engine must speed up to match the lower gear. With an electronic throttle, the ECU blips the throttle open to the value in this curve, by the engine speed the downshift has to reach (the lower gear's speed at the road speed), and closes it again.
Quick cal, in the settings, gives calculated starting values for the curve.
Rev matching needs an electronic throttle. With a cable throttle, the throttle cannot be blipped.
Open Torque tables settings under the tables.
| Setting | What it does |
|---|---|
| Reference | The engine's reference (maximum) torque in Nm, sent to the gearbox controller, which works its torque figures out against it. Set it to your engine's real peak torque |
| Idle up in Drive | Raises the idle speed by this many rpm while an automatic gearbox is in gear, so the engine does not labour against the torque converter at a stop |
| Idle output increase in Drive | Opens the idle valve this much more while in gear, for the same reason |
| Pedal kick down | The pedal position, in %, above which the ECU asks the gearbox for a kickdown |
| ETB blip delay | How long after the gearbox starts a downshift the throttle blip begins, in ms |
| ETB blip time | How long the throttle blip lasts, in ms (30 ms at least). The throttle opens to the Throttle rev match value and closes again evenly over this time |
| No blip below | No throttle blip below this road speed, so the car does not lurch on downshifts as it comes to a stop. 0 blips at any speed |
| Torque intervention method | How the ECU takes torque off when the gearbox asks (below) |
With the BMW E46 SMG, the gearbox matches the revs itself through the Throttle rev match table alone, and ETB blip delay and ETB blip time are not used; the page then also shows Close ETB on upshifts.
| Method | How torque is taken off | Character |
|---|---|---|
| Retard | Ignition retard in proportion to the request | The smoothest; the reduction it can give is limited |
| Retard and ign. cut | Retard for the fine steps, ignition cuts for the large ones | Smooth and fast: a good choice for most gearboxes |
| Ignition cut | Skips sparks in proportion to the request | Very fast and strong, but rough, and hard on the catalyst |
| Retard and fuel cut | Retard for the fine steps, fuel cuts for the large ones | Fast; the cut cylinders run lean for a moment |
| Fuel cut | Skips injections in proportion to the request | Strong; can give a lean or rich spike as the fuel returns |
Modern automatic gearboxes set their clutch pressures and shift timing from the engine's torque. With realistic torque figures, the gearbox behaves as if the RM-Primis ECU were the original engine controller.
Check the Engine torque table against the engine's real torque, especially at part load, and the Reference torque. Then check the Torque intervention method is taking enough torque off during shifts.
Contact customer support at [email protected].
Related pages: 8HP CAN bus and transmission · 8HP Performance Package · Electronic throttle · Ignition table