The RM-Primis ECU runs the ZF 8HP automatic gearbox over the CAN bus, as the original BMW engine controller would: it sends the TCU the engine's torque, speed and pedal, takes its torque requests during shifts, works the gear lever and paddles, and reads and clears the gearbox's fault codes and clutch adaptations. Everything is set up from RM-Tuner, with no other programmer.
For the 8HP's own shift points, transbrake, bump and virtual clutch, see the 8HP Performance Package.
The 8HP's controller (the TCU) is a computer of its own that decides when and how to shift, and it expects to talk to an engine controller all the time. Over the CAN bus, many times a second:
The TCU uses the engine torque to set its clutch pressures, so the torque tables matter as much as the CAN setup: with realistic torque figures, the gearbox shifts as it did behind its original engine. The RM-Primis also works the gear lever and paddles, and can read and clear the gearbox's own fault codes and clutch adaptations.
| Wiring | The TCU's CAN wired to the ECU, as in the 8HP wiring diagram |
| TCU power | A delay relay that keeps the TCU powered for at least 45 seconds after the ignition is switched off: the TCU saves its clutch adaptations then |
| RM-Tuner | The latest version, from Download Software |
Open Setup → CAN bus → Settings.
| Setting | What to choose |
|---|---|
| Speed | 500kbps, the 8HP's CAN speed |
| Resistor | On when the ECU is at one end of the CAN bus, as with the TCU wired directly to it. Off when it joins an existing bus that is already terminated at both ends |
| Broadcast (OEM chassis) | The original car's messages, when the dashboard, ABS or other modules of the car need them to keep working. BMW Fxx series, BMW E6x/8x/9x and others; options marked * are of limited test |
| 8HP shifter: Shifter Type | The gear lever: BMW F-Series, or emulation of a Sequential or Dodge shifter |
| 8HP shifter: Paddles | BMW (OEM Protocol) or Sequential (emulation): see Paddle and sequential shifters |
| Model | BMW 8HP |
| Clear DTCs on power cycle | Clears the gearbox's stored fault codes at every start. Some codes are expected when the TCU runs with a non-original engine controller |
With Model set to BMW 8HP, the 8HP gearbox and 8HP settings pages appear in the CAN bus menu.
| Setting | What it does |
|---|---|
| 8HP Performance Mode | Switches on the 8HP Performance Package, when it is installed in the TCU |
| Wheel circumference | The driven wheels' rolling circumference in mm, for the road speed. The Tyre size calculator works it out from a tyre size: enter width, profile and rim, and press Use circumference |
| Final drive ratio | The differential ratio |
| Transfer case ratio | For four-wheel-drive cars with a transfer case; 0 without |
| Speed correction | Fine correction of the road speed, in % |
| Wheel speed | The road speed the ECU works out, live |
| Driving mode | The mode the gearbox starts in: Eco Pro, Comfort, Sport, Sport+, or Performance Pack with the Performance Package. The shifter's mode button steps through them |
| Section | What it does |
|---|---|
| Information: Read | Reads the TCU's identification (VIN and software versions), its Status and the battery voltage |
| Information: Unlock | Prepares the TCU to work with the RM-Primis. RM-Tuner reads the TCU, saves a backup, downloads what it needs from our server and writes it. It takes a few minutes and asks you to confirm each step |
| Differential | TCU used ratio, the final drive the TCU works with, and Calculated ratio, the one measured from wheel and output shaft speeds. They should match |
| Adaptations: Read / Reset | The learned pressure and time of each clutch, A to E. Reset clears them, and the TCU learns again |
| Fault codes: Read / Clear | Reads and clears the gearbox's fault codes |
Before Unlock, connect a battery charger and keep the laptop on mains power. Never switch anything off while it runs. If power or communication is lost, RM-Tuner recovers the TCU from its backup; if that fails, contact us.
The 8HP accepts these final drive ratios: 2.35, 2.47, 2.56, 2.81, 3.08, 3.15, 3.23, 3.38, 3.46, 3.64, 3.73, 3.91, 4.10 and 4.27. If Calculated ratio differs from TCU used ratio, check Final drive ratio, Wheel circumference and Speed correction on 8HP settings.
The 8HP shifts by engine torque: set up the Engine torque table and the torque reduction on Torque tables before driving, or shifts will be harsh or slow.
Yes. The RM-Primis talks to the 8HP's own TCU over CAN, as the original BMW engine controller does. You need the TCU, its wiring to the ECU and the setup on this page.
Some codes are expected with a non-original engine controller and do not affect driving. Tick Clear DTCs on power cycle.
Contact customer support at [email protected]. 8HP wiring and accessories: rmracingelectronics.com.
Related pages: 8HP Performance Package · Paddle and sequential shifters · Torque tables · 8HP wiring diagram