The RM-Primis ECU controls an electronic throttle body (drive by wire, fly by wire) through its throttle control module: it reads the two accelerator pedal sensors and the two throttle position sensors, works out the throttle opening you want from the pedal and engine speed, and drives the throttle motor to hold it. The idle control, rev matching on downshifts and traction control all act through the same throttle.
Both pedal sensors and both throttle sensors are checked against each other continuously. If they disagree, or a sensor fails, the module goes to a safe state.
With a cable, your foot moves the throttle directly. With drive by wire there is no cable: your foot moves a pedal sensor, and a small electric motor moves the throttle plate.
Because the pedal and the throttle are separate, you decide how the car responds to your foot: a gentle, progressive pedal for a road car, a sharp one for the track, or a soft first part of the travel that makes a powerful car easier to drive in traffic.
Open Setup → Electronic throttle. The group is in the menu when the ECU reports a throttle module.
| Page | What it holds |
|---|---|
| Gauge | Live dials (or bars) for the pedal, throttle, target, motor drive and temperature, and the sensor diagnostics |
| Settings | Pedal and throttle calibration, control limits, the positioning PID and the module's firmware version |
| Tuning | The Throttle target table: throttle opening by engine speed and pedal |
| Feed-forward | The feed-forward correction and holding PWM curves, with their quick calibrations |
| Module firmware | Updating the throttle module's own firmware |
| Gauge | What it shows |
|---|---|
| Pedal Signal 1 / 2 | The two accelerator pedal sensors, in %. They should move together |
| Throttle Signal 1 / 2 | The two throttle position sensors, in %. They should move together |
| Throttle Target | The opening the module is aiming for |
| PWM | The drive to the throttle motor; negative values drive it closed |
| Target Error | The difference between the target and the actual opening |
| Temperature | The throttle module's board temperature |
Dials or Bars switches the view. The Live values panel beside them shows the motor current, the target error, the status bits and the module's own check of each sensor:
| Check | Meaning |
|---|---|
| OK | No error |
| Short to ground | The signal is at 0 V: a short or a broken supply |
| Short to V+ or not connected | The signal is at the supply voltage: a short, or the sensor is unplugged |
| Out of range | The signal went past the configured safety margin, or the two sensors disagree |
Disable ECU integration turns the electronic throttle integration off, for a car that has the module fitted but runs a cable throttle.
| Section | Setting | What it does |
|---|---|---|
| Calibrations | Released / Full pressed | Records the pedal sensors with the pedal fully up, then fully down |
| Calibrate | Learns the throttle's fully closed and fully open positions | |
| Control Options | Minimum / Maximum position deviation tolerance | How far the throttle may be from its target, in %, before the module treats it as a fault |
| Current limiting | Limits the motor current to the value beside it, to protect the motor | |
| Maximum board temperature | Above this the module protects itself | |
| Maximum control for idle | The most extra opening the idle control may add on top of the target table | |
| Module | Firmware version / Update | The module's firmware, and updating it |
| Positioning PID | P, I, D | How hard the module drives the throttle to its target |
| Autotune | Measures the throttle and works out the PID |
The Throttle table sets the opening for each pedal position (down) and engine speed (across). A straight 1:1 table gives the throttle exactly what the pedal asks; a table that opens less at small pedal makes the car calmer to drive, more makes it feel sharper.
Shaping the pedal. An engine makes most of its torque change in the first part of the throttle opening: at low revs, 30 % throttle can already give most of the full-load torque. A straight table therefore feels jumpy at the start of the pedal travel and dead at the end. Most road cars feel best with a gentle curve: for example 10 % pedal giving 5 % throttle, 50 % pedal giving 35 %, and 100 % pedal giving 100 %. At high revs the engine needs more opening to make the same torque, so the curve can be steeper there. Always reach 100 % throttle at full pedal at every speed, or the engine never gets full power.
The value at 0 % pedal is the idle opening: the idle control works upwards from it (see Idle control). The table tools are described on the Fuel table page.
| Curve | What it does |
|---|---|
| Feed-forward correction | Adds motor drive by the target error, so the throttle answers quickly before the PID has built up |
| Holding PWM | The drive that holds the throttle still at each opening against its return spring |
Quick cal fills each curve with a starting shape. Autotune: Holding PWM has the module measure the holding drive at each opening: it takes several minutes, with the engine stopped; check the curve afterwards. After changing these curves, check the PID again.
Keep your hands away from the throttle body whenever the ignition is on: the throttle can move at any time, and with force.
The throttle module moves the plate with three things working together: the holding PWM keeps the plate still against its return spring, the feed-forward gives it a push as soon as the target moves, and the PID corrects what is left. Tune them in that order, with the engine stopped and the ignition on, watching the target error on the Gauge page or in a log.
| What the throttle does | What to change |
|---|---|
| Drifts from the target when the pedal is held still | The holding PWM at that opening: run its Autotune again, or raise or lower the curve there |
| Responds slowly to a quick pedal movement | More feed-forward; then a little more P |
| Overshoots and comes back on a quick movement | Less feed-forward or less P; a little D to damp it |
| Buzzes or hunts at a steady opening | Less P or I; check the holding PWM there |
| Small steady error at some openings | More I |
| Sensor fault, throttle goes to its rest position | The two throttle sensors or the two pedal sensors disagree, or a signal is out of range: check their wiring, the Gauge page's sensor checks, and recalibrate |
Why two sensors. The pedal and the throttle each have two sensors that read the same position in different ways. The module compares them all the time, and also checks that the throttle stays within the position deviation tolerances of its target. If either check fails, it stops driving the motor and the return spring takes the plate back to its rest position. That is the safety of drive by wire: a broken wire, a worn sensor or a stuck plate cannot hold the throttle open by itself.
Check the result on the road. Log the pedal, the throttle target and the throttle position on a drive with gentle and sharp pedal movements. The throttle should follow its target within a few percent, with no overshoot on a quick stab of the pedal.
The module has gone to its safe state. Fix the sensor or wiring the check names, then switch the ignition off and on.
Run Autotune for the PID and the holding PWM again. If it still hunts, lower P a little.
Contact customer support at [email protected].
Related pages: Electronic throttle wiring · Torque tables and rev matching · TPS calibration