Everything the ECU does is timed from the crank and cam signals. If a tooth is missed, a gap is misread or the cam edge sits in the wrong place, the engine will not start, will misfire at high speed, or will lose sync for no visible reason. Guessing at those faults wastes hours. The Trigger analyzer shows exactly what the ECU sees on its trigger inputs: every crank tooth, the missing-tooth gap, the cam edges, the moment sync was found and where each spark fired. The VR analyzer shows the raw waveform of a VR (magnetic) sensor and the edge the ECU took from it, so you can see whether the signal itself is healthy.
This page explains how to read a capture, what a healthy trigger looks like, and how to find the common faults.
Open Scope in the rail on the left, then Trigger analyzer or VR analyzer. The analyzer takes captures from the ECU while the engine is cranking or running. Undock puts it in a window of its own, so you can change settings while you watch it.
Every datalog also saves one crank and cam capture as the engine starts: open it from the Datalog viewer with Recorded trigger (see Datalogging).
The chart shows the capture over crank degrees (or time):
| Channel | What it shows |
|---|---|
| Tooth periods | The time between each crank tooth and the one before, in µs. Even teeth make a flat band; the missing-tooth gap stands up as a spike, here every 360° |
| Expected | Where the ECU expects each gap, from the trigger pattern you set |
| Crank | The crank teeth themselves |
| CAM 1 / CAM 2 | The cam signals |
| CAM sync / Crank sync | When the ECU found the cam phase and the crank position |
| Ignition | The moment each spark fired |
The Capture summary gives the engine speed, the trigger wheel, the number of teeth logged and whether sync was held. The Decoded analysis checks the pattern for you:
| Reading | What a healthy 60-2 wheel shows |
|---|---|
| Ratio | The gap's period against a normal tooth: about 3.00 for a 60-2 wheel (two missing teeth) |
| Teeth between gaps | 58 |
| Jitter | How uneven the normal teeth are: a few tenths of a percent at a steady speed |
| Sync state | sync held |
| Cam edge | Where the cam edge falls after the gap: it must stay well clear of the gap itself |
The status line at the bottom says Trigger decode OK when the tooth pattern and the sync signals look right, or names what is wrong. Point anywhere on the chart to read the crank angle, the tooth number, the time and which signals are high there.
The toolbar. Crank teeth or VR waveform chooses what the ECU captures; Crank degrees or time sets the horizontal scale; - and + zoom, Fit shows the whole capture, Hold stops new captures so you can read the one on screen; Save... and Open... keep a capture as a file and read it back; Settings sets the colours.
A VR (variable reluctance) sensor is a magnet with a coil round it. As each steel tooth passes, the magnetic field through the coil rises and falls, and the coil makes an alternating voltage: one swing positive and one negative per tooth. Two things follow from that, and they are why the VR analyzer exists:
With VR waveform chosen as the capture mode, the ECU records the sensor's raw voltage instead of the teeth it counted from it: 512 samples, one every 0.1 ms, a little over 51 ms of signal.
Reading the waveform. The red trace is the sensor's voltage, centred on its quiet level. The blue line under it, comparator, is the decision the ECU made from it: one step for every tooth it counted. In the picture, a 60-2 wheel at 1000 rpm:
The Capture summary gives the peak-to-peak voltage, the number of edges, the length of the capture and the engine speed those edges add up to; the status line says whether the waveform looks usable.
What to check with it.
| What you see | What it means | What to do |
|---|---|---|
| A clean sine per tooth, comparator stepping once per tooth | A healthy signal | Nothing |
| A very small signal while cranking (well under 1 V) | The sensor is too far from the wheel, or the wheel is small or slow | Check the air gap (usually 0.5–1.0 mm); lower the threshold at cranking speed |
| Extra comparator steps between teeth, or spikes on the trace | Electrical noise: ignition leads, an unshielded cable, a poor ground | Use a shielded, twisted pair with the shield grounded at the ECU end only; route it away from coils and leads; raise the threshold where the noise is |
| The comparator misses teeth at high speed | The threshold is too high there, or the signal is clipping | Check the threshold curve against the signal's size at that speed |
| The gap looks distorted: a large swing on the wrong side, or the comparator stepping inside the gap | The sensor is wired the wrong way round: the ECU sees the inverted signal and counts the wrong edge, which also shifts the timing | Swap the two sensor wires, then check the base timing again with a timing light |
| The signal changes size with every tooth, rising and falling over a revolution | A bent or off-centre trigger wheel, or a loose sensor | Check the wheel's run-out and the sensor's mounting |
Check the VR waveform at cranking speed on every new installation, and again at the speed where any misfire or loss of sync appears. Most VR problems are visible here long before they can be found any other way.
See Trigger inputs and VR threshold for the threshold curve and the edges.
| What the capture shows | Likely cause |
|---|---|
| No teeth at all | The sensor is not wired to the input set for the crank, or has no supply (Hall sensor) |
| Teeth between gaps is not what the wheel has | Missed teeth (signal too weak at cranking, or threshold too high) or extra teeth (noise) |
| The ratio is far from the expected value | Missing or extra teeth around the gap, or the wrong trigger pattern set |
| Sync found, then lost at higher speed | A VR signal outgrowing its threshold, or noise at speed: check the VR threshold and the wiring |
| The cam edge sits right next to the gap | The cam reading is marginal: move the cam edge setting, or check the cam's timing |
| Ignition marks in the wrong place | The trigger offset: check base timing with a timing light (see Crank and cam sensors) |
Take a capture while cranking and another at idle before the first start of a new installation. A clean trigger is the foundation of everything else.
Open Scope → Trigger analyzer and crank the engine. The status line should read Trigger decode OK, the teeth between gaps should match your wheel and sync should be held.
Yes: Save... keeps the capture as a file. Send it with your tune to support.
Take a capture at the speed where it happens. Extra teeth or a ratio that drifts point at noise or the VR threshold; check the sensor's wiring, its shield and the threshold table.
Contact customer support at [email protected].
Related pages: Trigger inputs and VR threshold · Crank and cam sensors · Datalogging · Diagnostics