A tune is only as good as the data behind it. A datalog records everything the engine and the ECU do, many times a second, so you can replay a pull, find the moment a cylinder knocked, see where the mixture went lean or prove that a change worked. The RM-Primis logs two ways: to the laptop through RM-Tuner while you are connected, and to its own SD card, by itself, every time the car is driven.
This page explains both, how to set the SD card to log exactly when you need it, and how to read a log in the Datalog viewer.
With RM-Tuner connected, press Start log in the toolbar. RM-Tuner records every live value the ECU sends until you press it again, and saves the log to your logs folder. Use it on the dyno, on a test drive with a passenger at the laptop, and whenever you change something and want to see the effect.
Start a log before you make the change you want to check, and leave it running a few seconds after. A log that starts after the event shows nothing.
The SD card logs without a laptop, so you can capture what happens on a track day, a long drive or the one time a fault appears. The ECU starts and stops a log by itself on the triggers you choose.
Open Analyze → SD log.
| Button | What it does |
|---|---|
| Read the card again | Reads the list of logs from the card |
| Set the card's clock | Sets the ECU's clock to your computer's time, so each log is stamped with the right date |
| Start log | Starts a log on the card now |
| Transfer selected... | Copies the selected logs to your computer, ready for the Datalog viewer |
| Delete | Deletes the selected logs from the card |
Card shows the card's size and the ECU's date and time. Logs go to the folder you choose when transferring; RM-Tuner remembers the last one.
How the card logs. The ECU writes to the card by itself, whether or not a laptop is connected. Whenever one of the triggers below is active it records, and a long recording is split into numbered files of up to about 10 MB each, so a whole track day becomes a row of files you can pick from by their date and time. Nothing is lost when the laptop is unplugged or the car is switched off: what was written stays on the card until you delete it.
Reading them. With RM-Tuner connected, Read the card again lists the files, Transfer selected... copies them to your computer, and the Datalog viewer opens them like any other log. Copying is faster than the drive was long, but a full card still takes a while: transfer the files you need rather than all of them.
Looking after the card. Delete what you have transferred, so the card does not fill up, and set the card's clock whenever the Card date and time look wrong (after the battery has been disconnected, for example), so the files keep the right dates.
| Trigger | What it does |
|---|---|
| Log on power up | Starts a log at power-up and keeps it for Duration seconds. With a long duration, every drive is logged |
| Log on protection(s) | Logs for at least 10 s whenever one of the ticked protections acts: rev limits, launch limits, flat shift, overboost, lean protection or anti-lag. The log shows what led up to it |
| Log on battery voltage | Logs while the battery voltage is above Min. voltage: with the engine running, typically, as the alternator charges |
| RPM based trigger | Logs while the engine is above On and stops below Off |
| Log on input voltage | Logs while a chosen input is above a chosen voltage: a dash button or a switch that starts a log |
Which to choose. For a road car, Log on battery voltage (just below the charging voltage) logs every time the engine runs. For a track car, an RPM based trigger logs the hard driving and leaves out the paddock. Log on protection(s) is worth leaving on in every car: if something ever goes wrong, the log is there.
Open Analyze → Datalog viewer and Open log... to load a PC or SD card log.
What to log for common jobs.
| Job | Values to watch |
|---|---|
| Fuel | RPM, MAP, lambda, lambda target, the fuel corrections, the injector duty |
| Ignition and knock | RPM, MAP, ignition advance, each cylinder's knock reading, knock retard |
| Boost | RPM, TPS, MAP, boost target, boost duty, gear |
| Idle | RPM, idle target, idle output, coolant, ignition advance |
Yes, to its SD card, on the triggers you choose on the SD log page.
Connect RM-Tuner, open Analyze → SD log, select the logs and press Transfer selected.... Then open them in the Datalog viewer.
Press Set the card's clock while connected, so the ECU's clock matches your computer.
Contact customer support at [email protected].
Related pages: Live data: monitor and dashboard · Diagnostics · Knock control · Adaptation table