The RM-Primis ECU measures the mixture with a wideband lambda sensor. It has a built-in wideband controller for the Bosch LSU 4.9 (and LSU 4.2) sensor, so the sensor plugs straight into the ECU, and it can also read an external wideband controller's 0–5 V output or a CAN wideband controller. The reading drives the closed loop, the adaptation (autotune) and your logs.
A wideband sensor sits in the exhaust and measures how much oxygen is left over after combustion. Lean exhaust has oxygen to spare; rich exhaust has none, and unburnt fuel instead. Inside the sensor, a small pump cell pumps oxygen in or out of a measuring chamber to keep it balanced, and the current needed to do that tells the controller exactly how rich or lean the mixture is, from very rich to very lean.
It only works hot: around 750 °C. A heater inside the sensor gets it there and holds it there, controlled by the ECU. That is why the reading appears a short while after the engine starts, and why a sensor that is not ready reads N.A.
The reading is only as good as the sensor's position: an exhaust leak before the sensor draws in outside air and makes the mixture read lean, and a sensor too close to the turbo or the exhaust valves can run too hot.
Open Setup → Sensors → Wide band lambda. The settings are in Wide band lambda settings under the calibration table.
| Setting | What it does |
|---|---|
| AFR scale / Lambda scale | Shows the mixture as AFR (using the stoichiometric ratio of the fuel chosen on Fuelling settings) or as lambda, everywhere in RM-Tuner, the Lambda table included |
| Enable AFR Sensor | Switches the wideband reading on |
| Sensor source | Where the reading comes from: Internal for a sensor wired to the ECU's own controller; Spare 1–5, Spare temp. 1–2 or MAF for an external controller's 0–5 V output on that input; or a CAN controller: rusEFI WBO, Haltech WBA1/2 or AEM |
| Quick cal | Fills the calibration table for the internal controller, or for common external controllers |
| Closed loop range | The mixture window the closed loop works in, as on Fuelling settings |
| Setting | What it does |
|---|---|
| LSU 4.9 sensor | Tick for an LSU 4.9; untick for an LSU 4.2 |
| PID Heater: P, I, D | The heater control that holds the sensor at its working temperature. Leave them as they are unless the sensor maker states otherwise |
| Sensor heater: Minimum / Maximum | The sensor temperature range within which its reading is used |
| Trend PID | A live graph of the heater control |
Choose the input the controller's output is wired to under Sensor source, then fill the calibration table with the controller's output curve (its voltage for each AFR), from Quick cal or the controller's manual. Set Min. and Max. for the external range so a disconnected controller is recognised.
| Value | What it shows |
|---|---|
| Input voltage | The sensor or controller signal |
| AFR (or lambda) | The mixture; N.A. while the sensor is not ready |
| Heater control, Pumpcell, Temp. | The internal controller's heater drive, pump cell current and sensor temperature |
| Current temperature | The sensor's temperature now |
A cold exhaust carries water, and water on a hot sensor can crack it. So, with the internal controller, the sensor is not heated until the engine runs, and while the coolant is below 40 °C it is held at a low heater voltage for its first few hundred engine cycles until the exhaust has dried out. The mixture reading arrives once the sensor is at its working temperature.
Mount the sensor in the upper half of the exhaust pipe, tilted at least 10° from horizontal so condensation drains away, and well before the catalyst. Use the sensor's own connector and never splice its wires.
A wideband sensor is only as good as where it is fitted. Everything the closed loop, the adaptation and your own tuning do rests on its reading.
Where to fit it.
What makes a reading wrong.
| Cause | What you see |
|---|---|
| Exhaust leak before the sensor | Leaner readings at idle and low load, fine at full load |
| Misfire | Lean readings: the unburnt air and fuel of the misfiring cylinder reach the sensor as excess oxygen |
| Cold sensor | No usable reading until Lambda ready, when the heater has brought it to working temperature (see the warm-up section above) |
| Overrun fuel cut | Very lean (free air): normal, the engine pumps air |
| Old or contaminated sensor | Slow response and a reading that drifts; leaded fuel, oil burning or coolant in the exhaust ruin sensors quickly |
The delay. The gas takes time to travel from the cylinder to the sensor, and the sensor time to respond: typically 50–150 ms at high load and several hundred at idle. When you read a log, line the lambda up with what the engine did a moment earlier, not at the same instant. The fuel closed loop allows for it (AFR control on Fuelling settings).
Yes: wire its 0–5 V output to a spare analog input and choose that input under Sensor source, or use a supported CAN controller (rusEFI WBO, Haltech WBA, AEM).
The sensor is not ready: it is still warming up, the engine has not run long enough on a cold start, or Enable AFR Sensor is off. With the internal controller, check Temp. rises to its working range.
Contact customer support at [email protected].
Related pages: Fuelling settings · Lambda / AFR target table · Adaptation table