The RM-Primis ECU reads the coolant temperature (CLT) and the intake air temperature (IAT) from thermistor sensors: their resistance, and so the voltage the ECU sees, changes with temperature. Every sensor type has its own curve, so the ECU needs a calibration table that turns the voltage into a temperature. Warm-up enrichment, the fuel and ignition temperature corrections, the radiator fan and the idle control all depend on these readings.
The coolant and air temperature pages work the same way.
How the sensor works. A temperature sensor is a thermistor: a resistor whose resistance falls as it warms up, from tens of thousands of ohms when very cold to a hundred or so when hot. The ECU feeds it from 5 V through a 1 kΩ resistor and reads the voltage across it: high voltage means a cold sensor, low voltage a hot one. Every sensor type has its own curve of resistance against temperature, which is why the ECU needs to be told which sensor you have.
Open Setup → Sensors → Coolant temperature or Intake air temperature.
| Table | The temperature at each sensor voltage, from the lowest voltage (hottest) to the highest (coldest) |
| Live values | Voltage from the sensor now and the Temperature the ECU reads from it |
| Enable CLT Sensor / Enable IAT Sensor | Switches the sensor on |
| Quick cal | Fills the table from a list of common sensors |
| Alarm limits | Max. Value and Min. Value: the voltage range a working sensor stays inside. Outside it the ECU stores a fault code and uses Default Temp. instead |
| Fahrenheit | Shows the temperatures in °F |
The table tools are described on the Fuel table page.
With a known sensor: press Quick cal and choose it from the list. Check the live Temperature against a thermometer.
With an unknown sensor, measure it:
Put the sensor in water with a thermometer, and measure its resistance (or the voltage at the ECU) at three or more temperatures, such as 20 °C, 50 °C and 90 °C, plus the hottest your engine reaches.
If you measured resistance, work out the voltage the ECU sees. The ECU's pull-up resistor is 1 kΩ to 5 V:
V = 5 × R_sensor ÷ (R_sensor + 1000)
Enter the voltages and temperatures into the table, and use Interpolate between them.
Check the live reading against a thermometer on the running engine.
Set Default Temp. to a safe value: the ECU uses it if the sensor fails. For coolant, a warm temperature such as 80–90 °C avoids running the engine on cold-start fuelling when warm.
The intake air sensor is calibrated in exactly the same way. On turbocharged engines, fit it after the intercooler, where it measures the air the engine actually breathes: the ignition and fuel corrections depend on it.
Few readings change as much of the tune as these two:
| Coolant temperature decides | Air temperature decides |
|---|---|
| Cranking and after-start fuel, and the warm-up enrichment | The air density correction of the fuel |
| The idle speed and the idle opening | The ignition retard for hot air, against knock |
| The ignition correction for a cold or hot engine | The flex fuel and boost corrections that use it |
| The radiator fans, the rev limit by temperature, overrun fuel cut, VVT and anti-lag enables |
A coolant sensor that reads 10 °C low makes a warm engine run its warm-up enrichment: rich, sooty and slow to idle down. An air sensor that reads 20 °C low on a hot day takes away the knock protection the air temperature curve was meant to give.
Fitting the coolant sensor. In the coolant flow, near the thermostat housing at the engine outlet, where it sees the engine's real temperature. Not in a dead pocket, and not after the radiator.
Fitting the air sensor. In the air the engine actually breathes: after the intercooler on a turbo engine, in the intake pipe or plenum. Keep it out of the sun of the exhaust manifold and away from the engine's heat: an air sensor on a hot plenum reads the plenum, not the air, and heat soak at idle then makes the ECU think the air is far hotter than it is. A sensor with an open tip responds in seconds; a closed brass one can take a minute to follow a change.
Checking them. On a cold engine that has stood overnight, both should read the air temperature in the garage within a couple of degrees. Watch the coolant reading rise smoothly to the thermostat's opening temperature as the engine warms, then hold there. A reading that jumps or drops out points at a connector or a ground.
Check the sensor type with Quick cal, then the live Voltage: about 0.4 V means a very hot or shorted sensor, close to 5 V means a cold or disconnected one. Check the wiring and the ground.
The voltage left the Alarm limits. The sensor is disconnected, shorted, or the limits are too tight for its range.
Contact customer support at [email protected].
Related pages: Coolant and air temperature fuel trims · Coolant and air temperature ignition corrections · Cold start and warm-up enrichment