The rev limiter is the engine's last line of defence against over-revving: a missed gear, a wheel leaving the ground or a driver holding a gear too long. Too harsh a limiter jerks the car and stresses the drivetrain; too soft and the engine floats past its limit. The RM-Primis limits the speed by cutting sparks, fuel or both, with a soft limiter that eases the engine onto the limit and a limit that can be lower while the engine is cold.
This page explains how the limiter works, how to set it for a road car or a race car, and how it works together with launch control and flat shift.
The limit follows the coolant temperature. The Rev limiter table holds the limit by coolant temperature, so a cold engine, with thick oil and tight clearances, can be held to a lower limit until it warms up. In the example the limit is 4500 rpm below freezing and rises to 7000 rpm from 70 °C.
The soft limiter. From Soft limit delta below the limit, the ECU starts to hold the engine back:
Ignition cut or fuel cut?
| Ignition cut | Fuel cut | |
|---|---|---|
| How it feels | Sharp and precise: the engine is held right at the limit | Softer, with the engine dipping and recovering |
| Exhaust | The unburnt fuel of the cut cylinders goes into the exhaust: pops and heat, hard on a catalyst and a turbo | Clean: nothing is burnt in the exhaust |
| Typical use | Race cars, launch control, flat shift | Road cars, engines with a catalyst |
With launch control and flat shift the limit is their own Hard rev limit, and the launch cut starts at launch control's Rev limit, using this page's Ignition event cut and Gain. See Launch control and flat shift.
Open Safety → Limits & protections → Rev limiter. The table is at the top and the settings are under Rev limiter settings below it.
| Setting | What it does |
|---|---|
| Rev limiter table | The rev limit by coolant temperature |
| Fuel cut | Cuts all injection from Soft limit delta below the limit |
| Ignition cut | Cuts sparks in the soft zone, rising to 99 % at the limit |
| Gain (and Current gain) | Shapes how the spark cut rises. At 1.000 it rises in a straight line from Ignition event cut to 99 %. Below 1.000 the cut starts later and rises faster; above 1.000 it starts higher and rises more gently |
| Soft limit delta | How far below the limit the soft limiter starts, in rpm |
| Ignition advance correction | Added to the timing in the soft zone, whether or not a cut is on; negative retards |
| Ignition event cut | The share of sparks cut where the soft zone starts |
| Shift light | The engine speed at which the shift light comes on, for dashboards and instrument clusters that show it over CAN |
| What happens | What to change |
|---|---|
| The engine overshoots the limit by a few hundred rpm | Larger Soft limit delta, higher Ignition event cut, or a lower Gain |
| The limiter feels harsh and jerky | Lower Ignition event cut, a higher Gain so the cut rises more gently, or a little negative Ignition advance correction |
| The engine stops short of the limit | Smaller Soft limit delta or Ignition event cut |
| Loud bangs in the exhaust on the limiter | That is the ignition cut burning fuel in the exhaust: use Fuel cut on the road |
A limiter that starts working a little below the limit and grows stronger as the engine approaches it, so the engine settles on the limit instead of hitting a wall. On the RM-Primis it starts at Soft limit delta below the limit.
Fuel cut on a road car, especially with a catalyst: it sends no unburnt fuel into the exhaust. Ignition cut on a race car, where its sharper, more precise action matters more than the exhaust.
The Rev limiter table follows the coolant temperature. A low limit while cold protects an engine whose oil has not yet warmed up and thinned out.
Yes: launch control has its own limits, active while the clutch is pressed at a standstill. See Launch control and flat shift.
Contact customer support at [email protected].
Related pages: Launch control and flat shift · Engine protection · Knock control · Overrun fuel cut