A standing start is won or lost in the first second. Rev the engine too little and it bogs as the clutch bites; too much and the tyres go up in smoke. Launch control holds the engine at the speed you choose, with the throttle wide open, so every start is the same: foot flat, clutch out, go. Flat shift (also called no-lift shift) uses the same clutch switch for the gear changes: you keep the throttle pinned, press the clutch, and the ECU cuts the engine just long enough to change gear without over-revving it.
This page explains how the RM-Primis does both, how to set them up, and how to tune them for a naturally aspirated or a turbocharged engine.
Both work by cutting sparks while the injectors keep firing, so unburnt fuel burns in the exhaust. That is hard on the exhaust manifold, the turbo and the catalyst, and launches are hard on the clutch and the drivetrain. Keep launches short, and do not use either on a road car whose catalyst you want to keep.
Launch control is active while all of these are true:
Below Rev limit nothing changes: the engine revs up on its normal fuel and timing. As it passes Rev limit, launch control takes over:
The engine settles where the cut balances the open throttle: just above Rev limit on a gentle engine, closer to Hard rev limit on a powerful one. The moment the driver lets the clutch out, launch control lets go and the engine pulls on its normal tune.
Why the timing matters. On a naturally aspirated engine a modest launch timing keeps the engine from banging against the cut and limits the heat. On a turbocharged engine, retarded timing with a little extra fuel sends heat into the exhaust and spools the turbo on the line, so the car leaves with boost already built.
Flat shift is active while all of these are true:
While it is active the timing is Ignition absolute timing, and every spark is cut above launch control's Hard rev limit. In practice that means:
Open Tune → Motorsport → Launch control / Flat shift. Both need the clutch switch, set under I/O → Inputs & outputs → Special functions → Clutch switch (see Special functions), and launch control takes its cut ramp from Safety → Rev limiter.
Changes to launch control and flat shift take effect the next time the ignition is switched on. After changing them, store the tune and switch the ignition off and on.
| Setting | What it does |
|---|---|
| Enable Launch | Switches launch control on |
| TPS Threshold | Launch control works only with the throttle at or above this. 70–90 % is typical, so a part-throttle pull away in traffic never triggers it |
| Rev limit absolute timing | The ignition timing while launch control is active. It replaces the calculated timing, knock and temperature corrections included. Keep it within ±59.9° |
| Rev limit | Launch control is active above this engine speed: the launch timing and fuel apply and the spark cut starts |
| Hard rev limit | Every spark is cut above this speed while launch control or flat shift is active. It replaces the normal rev limit while they are active |
| Fuel compensation | The fuel change while launch control is active: +5 % adds fuel, -5 % takes fuel away. The lambda target moves with it and closed-loop lambda correction pauses |
| Vehicle speed threshold | With a road speed signal (wheel speed sensor or CAN), launch control works up to this speed and flat shift above it |
| Setting | What it does |
|---|---|
| Enable Flat Shift | Switches flat shift on |
| Activation | Clutch: pressing the clutch starts it. Gearbox: the gearbox asking for less torque over CAN starts it (automated and automatic gearboxes such as the BMW SMG, DSG or ZF 8HP set up on the CAN bus page); launch control still uses the clutch |
| Launch / Flat threshold | The engine speed at the moment the clutch is pressed decides what it is for: below it, launch control; above it, flat shift |
| Flat shift window | Flat shift stays active while the engine is above the clutch speed minus this |
| Ignition absolute timing | The timing while flat shift is active and sparks are allowed |
Clutch status shows Pressed or Released once a clutch switch is assigned (Disabled until then), and Active now shows what the ECU is doing: launch control, flat shift, anti-lag or none. Press the pedal and check it follows; if it reads the wrong way round, change the input's edge on the Special functions page.
Tuning the launch. Log the engine speed, the wheel speed (if fitted), the boost and the lambda over a few launches:
| What happens | What to change |
|---|---|
| The engine bogs as the clutch bites | Raise Rev limit, or (turbo) build more boost on the line with more retard and fuel |
| The tyres spin away on the launch | Lower Rev limit; on a turbo engine, less boost on the line; add traction control |
| The engine bounces hard against the cut | Lower the launch timing; check the rev limiter's cut ramp is not too steep |
| The exhaust glows or pops violently | Less retard, less fuel compensation, shorter launches |
| Launch control never engages | Clutch status, the throttle against TPS Threshold, the engine speed against Rev limit, and whether the car is already above Vehicle speed threshold |
With Activation set to Gearbox, a sequential or automatic gearbox on the CAN bus starts flat shift by itself at every gear change it asks for. The driver needs no clutch.
They are the same idea: a second, lower rev limit for standing starts, active while the clutch is pressed. The RM-Primis adds its own launch timing and fuel, and a cut that grows gradually between two speeds, so the engine sits steadily instead of bouncing off a hard limit.
Changing gear without lifting off the throttle. The ECU cuts the engine while the clutch is pressed so it does not over-rev, and the engine is ready to pull in the next gear the moment the clutch comes out.
Yes, with retarded Rev limit absolute timing and a little extra fuel: the late combustion sends heat and energy into the exhaust, which spools the turbo while the car is standing still. Keep launches short to protect the turbo and the manifold.
Check Clutch status reads Pressed with the pedal down, the throttle is above TPS Threshold, the engine is above Rev limit, and the car is not already moving faster than Vehicle speed threshold. Remember that changes take effect after the ignition is switched off and on.
Contact customer support at [email protected].
Related pages: Rev limiter · Anti-lag · Traction control · Special functions · Ignition table