A tyre gives its best grip with a little slip, typically somewhere between 5 and 15 % depending on the tyre and the surface. Below that you are leaving acceleration on the table; above it the tyre is spinning, grip falls away and the car slows down, slides or both. Traction control watches the driven wheels against the undriven ones and, the moment the slip goes beyond what you allow, takes torque away from the engine until the tyres hook up again.
This page explains how the RM-Primis traction control measures slip, how it decides how much torque to take away, and how to set it up and tune it for a launch, a wet road or a track.
Measuring slip. The ECU compares the speed of the driven wheels with the speed of the undriven ones, which roll freely and show the car's true speed:
slip = (driven wheel speed − undriven wheel speed) ÷ driven wheel speed
At 100 km/h on the undriven wheels and 110 km/h on the driven ones, the slip is about 9 %. The wheel speeds come from wheel speed sensors wired to the ECU, or from the ABS module over CAN.
Deciding how much slip is allowed. The Slip table holds the most slip you allow, by road speed and throttle position. A launch from rest can use more slip than a car at 150 km/h, and a driver feathering the throttle can be left alone while one at full throttle is helped.
Taking torque away. When the slip goes above the table, a PID controller asks for a torque intervention, from 0 to 100 %, and the ECU delivers it with the method you choose: retarding the timing, cutting sparks, cutting fuel or lowering the boost, or a mix. Timing retard is smooth and fast; cuts are stronger; boost reduction is gentle but slow. The controller keeps adjusting until the slip is back at the target, then hands the torque back.
The same torque intervention method also delivers the torque reductions an automatic gearbox asks for at its gear changes.
Open Tune → Motorsport → Traction control:
| Page | What it holds |
|---|---|
| Overview | Enable, the torque intervention method, the override switch and the wheel speed sensors |
| Slip table | The most slip allowed, by road speed and throttle |
| PID | The controller, its output limit and the live values |
| Transfer case | For BMW xDrive transfer cases: the split by engine speed and load |
| Setting | What it does |
|---|---|
| Enable | Switches traction control on |
| Enable ABS as speed source | Uses the wheel speeds the ABS module sends on CAN instead of wheel speed sensors. Works with BMW E46, E9x and F-series ABS modules and with VW/Audi group ABS modules |
| Logarithmic response | Makes the intervention react more sharply to small amounts of slip |
| Torque intervention method | How the torque is taken away: Retard; Retard and ign. cut; Ignition cut; Retard and fuel cut; Fuel cut; Retard and boost reduction; Boost reduction. With the combined methods, the cut or the boost reduction does the coarse work in steps and the retard covers what is in between |
| Close ETB on upshifts | For the BMW E46 SMG gearbox: whether the electronic throttle may also close a little on upshifts |
| Override input and Learn | A switch that turns traction control off, for burnouts or a dyno run. Learn teaches the ECU the switching point of an analog input used as a switch |
| Inverted | Reverses the override switch: active when the voltage does not match |
| Minimum speed | Below this road speed traction control does not intervene |
| Speed sensors | The calibration of the driven (Tractioned wheels) and undriven (Untractioned wheels) wheel speed sensors, in pulses per metre, with Learn |
| Signal filter | Smooths the wheel speed signals. Use the lowest value that gives a steady reading: filtering delays the signal |
Calibrating the wheel speed sensors. Drive at a steady, known speed (check it with GPS), type it in Speed with KM/H or MPH chosen, and press Learn for each sensor. The ECU works out the pulses per metre. Then drive in a straight line at a steady speed: the two wheel speeds in the live values should agree, and Wheel traction should read 100 %.
The most slip allowed before traction control steps in, in %, by road speed (the undriven wheels) across and throttle position down. In the example:
How to choose the numbers. Log a few launches and pulls with traction control off: the slip at which the car accelerates hardest is the right target for that tyre and surface. Street tyres usually like less slip than slicks; a wet road needs less again.
| Setting | What it does |
|---|---|
| P, I, D | The controller's gains: I builds the intervention while the slip stays above the target, P reacts to how quickly the slip is changing, D to how quickly that is changing |
| Gain | Multiplies the whole PID output |
| Loop speed | How often the controller updates, in ms. Traction control needs a fast loop: 20–50 ms |
| Trend PID | A live graph of the slip target, the slip and the intervention |
| Output limits: Maximum | The most torque intervention the controller can ask for. 50 % is a sensible start: enough to stop the wheels spinning without killing the engine |
| Minimum and Start value | Used only by Auto tune; the running loop does not use them |
The Live values panel shows the driven and undriven wheel speeds, the coolant temperature, the retard applied, the Wheel traction (100 % is no slip) and the Torque interv. being asked for, and the traction status.
| What happens | What to change |
|---|---|
| The wheels flare well beyond the target before anything happens | More I or Gain; a faster Loop speed; Logarithmic response |
| The intervention is too strong: the car bogs and the engine stumbles | Less Gain; a lower Maximum; allow more slip in the table |
| The engine surges on and off (cut, spin, cut) | Less P/I; more slip allowed; a smoother method (retard first) |
| It cuts in at low speed while manoeuvring | Raise Minimum speed, allow more slip at low speed and part throttle |
| Nothing ever happens | Enable; the wheel speeds in the live values; the override switch; the slip table values |
| It steps in when driving straight with no spin | The wheel speed calibration: check the two speeds agree at a steady speed |
A worked example. On a launch at full throttle the driven wheels reach 25 % slip at 20 km/h before the intervention catches them, then the car bogs. The slip target there is 12 %. Raising I makes the intervention start earlier, and lowering Maximum from 70 % to 50 % stops it taking so much torque that the engine falls on its face. The next launch holds the slip between 10 and 15 %.
For BMW xDrive transfer cases (BMW E-series ATCxx), the ECU can command the transfer case itself. Choose the Transfer case type and fill the Transfer case split table, by engine speed and load, with the split you want.
At least one driven and one undriven wheel speed, from sensors wired to the ECU's speed inputs (see Trigger inputs) or from a supported ABS module over CAN.
It measures slip against undriven wheels, which show the car's true speed. A permanent four-wheel-drive car has no undriven wheels, so traction control cannot measure slip that way.
It depends on the tyre and the surface: typically 5–10 % for street tyres on dry tarmac and 10–15 % for slicks or launches. Find it from your own logs: the slip at which the car accelerates hardest.
Yes, with the Override input: a switch on the dash that turns it off for burnouts, the dyno or a driver who wants it off.
Contact customer support at [email protected].
Related pages: Launch control and flat shift · Gear settings and boost by gear · Boost control · Trigger inputs · Torque tables