A turbocharger left to itself makes as much boost as its wastegate spring allows: open the wastegate at 0.5 bar and that is all the engine ever gets, in every gear and at every throttle opening. Boost control lets the RM-Primis decide instead. It drives a boost control solenoid that holds the wastegate shut beyond its spring pressure, so you can ask for exactly the boost you want at each engine speed and throttle opening, less in the low gears, more on E85, and less again when the tyres start to spin.
This page explains how the boost control works, how to set it up safely and how to tune the closed loop until the boost rises quickly, stops on target and stays there.
The wastegate and the solenoid. The wastegate actuator is a diaphragm and a spring: when the boost pressure on the diaphragm overcomes the spring, the wastegate opens, exhaust bypasses the turbine and the boost stops rising. A boost control solenoid sits in the hose to the actuator and bleeds part of that pressure away. The more of the time the ECU holds the solenoid open (its duty, in %), the less pressure reaches the actuator, the longer the wastegate stays shut, and the more boost the engine makes. With the solenoid at 0 % the engine runs on the spring alone.
Open loop or closed loop. The boost table works in one of two ways:
| Mode | What the table holds | How it behaves |
|---|---|---|
| Open loop | The solenoid duty in %, by engine speed and throttle | Simple and predictable, but the boost a given duty makes drifts with air temperature, altitude, fuel and exhaust back pressure |
| Closed loop | The target boost in kPa (absolute manifold pressure) | The ECU reads the MAP sensor and a PID controller moves the duty until the boost matches the target, within the output limits you set |
Closed loop is what most engines should run once the basics are known, because it holds the same boost on a cold morning and a hot afternoon.
Reading kPa. The RM-Primis measures absolute pressure: 100 kPa is roughly the atmosphere at sea level, so a target of 200 kPa is about 1 bar (14.5 psi) of boost and 250 kPa about 1.5 bar.
The table's axes. The table is read by engine speed across and throttle position down. That lets the part-throttle rows ask for less boost, which makes the car far easier to drive, and keeps the closed-throttle row at atmospheric pressure. The closed-throttle row is also what applies while anti-lag is active.
What else moves the target. The ECU scales the target (or the duty, in open loop) by:
Open Tune → Boost control. It has three pages:
| Page | What it holds |
|---|---|
| Overview | Enable, open or closed loop, the output and its frequency |
| Target boost | The table: target boost (closed loop) or solenoid duty (open loop) |
| PID | The closed loop controller and its output limits, with the live values beside them. Shown in closed loop only |
| Setting | What it does |
|---|---|
| Enable | Switches boost control on |
| Closed loop (hold the target MAP) | Off: the table is the solenoid duty. On: the table is a target pressure the ECU holds |
| Activate only while running | Holds the solenoid off while the engine is not running |
| Output pin | The ECU output that drives the solenoid. Make sure nothing else uses it |
| PWM frequency | The solenoid's drive frequency. Common three-port boost solenoids work at around 15–30 Hz; use the maker's figure |
| Invert output | For a solenoid plumbed so that it raises boost with the output off |
The example is a closed-loop table for a turbocharged engine:
In open loop the same table holds the solenoid duty in % instead.
Set the target only as high as the engine, the fuel system and the turbo can safely take, and set the overboost protection a little above the highest target before the first run.
The table tools (selection, smooth, interpolate, the 3D view) are described on the Fuel table page.
In closed loop the ECU compares the manifold pressure with the target at every update and moves the solenoid duty to close the gap.
| Setting | What it does |
|---|---|
| P | Responds to how fast the boost error is changing: it damps the boost as it approaches the target |
| I | Moves the duty in proportion to the error at every update: it does the work of reaching and holding the target |
| D | Responds to how fast that change is changing: it helps stop a spike as the turbo comes on |
| Gain | Multiplies the whole PID output: one knob to make the loop stronger or gentler without changing the balance of P, I and D |
| Loop speed | How often the PID updates, in ms. A faster loop makes the same gains stronger |
| Trend PID | A live graph of the target, the manifold pressure and the duty, for tuning by eye |
| Output limits: Maximum | The most duty the closed loop may use. Your safety net: the boost can never go beyond what this duty makes |
| Output limits: Minimum | The least duty the closed loop may use, whatever the target |
| Start value | Not used by the running loop |
The Live values panel shows the throttle, the actual MAP, the target and the valve output, so you can watch them while you tune.
Make full-throttle pulls in the same gear, with Trend PID open, and watch how the boost follows the target:
| What the boost does | What to change |
|---|---|
| Rises slowly and reaches the target late | More I; check Maximum is not holding the duty back |
| Spikes above the target, then settles | More P and a little D to damp it, or less I; a smaller target where the turbo spools |
| Surges up and down at steady full throttle | Less I and P, or a slower Loop speed |
| Settles a few kPa below the target | More I; check the solenoid hoses for leaks |
| Overshoots only in the low gears | Use boost by gear, or less target where the turbo comes on |
| Never gets above the spring pressure | The solenoid is not working: check its wiring, the output pin, Invert output and the hose routing |
A worked example. The target is 230 kPa at 4000 rpm. On the first pull the boost reaches 255 kPa at 3600 rpm and then falls back to 230 kPa: a 25 kPa spike as the turbo spools. Adding a little D and slightly more P brings the spike down to 238 kPa; lowering the 3000 and 3500 rpm targets by 10 kPa removes the rest.
Always tune boost with the fuel and ignition already safe for the boost you are asking for, and watch the knock and the lambda on every pull.
Open loop sets the solenoid duty straight from the table, so the boost changes with weather, temperature and altitude. Closed loop reads the manifold pressure and adjusts the duty to hold the target boost from the table.
The RM-Primis works in absolute pressure. Take away about 100 kPa (the atmosphere) to get the boost: 200 kPa is about 1 bar or 14.5 psi.
Yes, with boost by gear: each gear gets a percentage of the target. See Gear settings and boost by gear.
Yes: the boost compensation of Flex fuel scales the target with the ethanol content.
The solenoid is not reducing the pressure at the actuator. Check the output pin and wiring, that boost control is enabled, the solenoid's hose routing, and try Invert output.
Contact customer support at [email protected].
Related pages: MAP sensor · Gear settings and boost by gear · Engine protection · Anti-lag · Flex fuel