Knowing which gear the car is in opens up a lot: less boost in first and second where the tyres cannot use it, the gear shown on the dashboard, and the right engine speed for each gear when the gearbox asks for a rev match. The RM-Primis works the gear out by itself from the engine speed and the road speed, once it knows your gearbox's ratios, the differential and the size of the wheels.
This page explains how gear detection works, how to set it up (with the ECU learning the ratios for you), and how to use boost by gear.
In any gear, the engine speed and the road speed are tied together by the gearbox ratio, the differential ratio and the wheel's circumference:
engine rpm = wheel rpm × differential ratio × gear ratio
The ECU knows the engine speed and the road speed (from a wheel speed sensor or over CAN), so it divides one by the other and finds the gear whose ratio matches. When the car is stopped, or the engine speed matches no gear (in neutral), there is no gear.
A worked example with the values in the picture below: a 6-speed gearbox, differential 3.07, wheels with a rolling circumference of 1997 mm. At 100 km/h the wheels turn 100 000 m ÷ 60 min ÷ 1.997 m ≈ 835 rpm. In 5th (1.000) the engine turns 835 × 3.07 × 1.000 ≈ 2560 rpm; in 4th (1.240) it turns about 3180 rpm. When the ECU sees 2560 rpm at 100 km/h, it knows the car is in 5th.
Open Tune → Motorsport → Gear settings (see the menu on the Launch control page).
Type the tyre's width, profile and rim size (for a 205/55 R16: 205, 55 and 16) and press Use circumference to put the result in Wheel circumference. Nothing else is kept from the calculator.
| Setting | What it does |
|---|---|
| Gear count | How many forward gears the gearbox has |
| Differential | The final drive ratio, for example 3.07 or 3.46 |
| Wheel circumference | The driven wheels' rolling circumference, in mm: the distance the car rolls in one turn of the wheel. The ECU uses it to turn road speed into wheel speed |
| Gear 1 to Gear 9 | Each gear's ratio, from the gearbox's data or learned with Learn |
| Learn | Drive steadily in that gear and press its Learn: the ECU measures the ratio from the engine speed and the road speed |
| Setting | What it does |
|---|---|
| Enable boost by gear | Switches boost by gear on |
| Gear 1 to Gear 9 | The share of the boost target used in each gear, in %. 100 % is the full target; 70 % in first gear turns a 230 kPa target into 161 kPa |
Boost by gear works on the closed-loop boost target (see Boost control).
Measuring the wheel circumference on a drive. A tyre's real rolling circumference is a little smaller than the calculator's figure, because the tyre squashes under the car. To measure it, drive steadily in a gear whose ratio you know and read the road speed and the engine speed:
circumference (m) = road speed (m/s) × 60 × differential × gear ratio ÷ engine rpm
For example, 27.8 m/s (100 km/h) × 60 × 3.07 × 1.000 ÷ 2565 rpm = 1.996 m, so 1996 mm.
In the low gears the tyres cannot use full boost: the car spins its wheels, the traction control has to work harder and the drivetrain takes a beating. Boost by gear lowers the target there:
| Gear | Example | Why |
|---|---|---|
| 1st | 70 % | Least grip, highest torque multiplication |
| 2nd | 85 % | Still easily spins the tyres |
| 3rd | 95 % | Nearly full boost |
| 4th and up | 100 % | Full boost |
Start low and raise each gear's value until the tyres just hold at full throttle. The overboost protection and the boost control PID apply as usual.
No. It works the gear out from the engine speed and the road speed, once the ratios, the differential and the wheel circumference are set.
Check the wheel circumference and the ratios: drive steadily in each gear and compare the engine speed with the calculation in section 1. A wrong circumference makes every gear read wrong; one wrong ratio makes one gear read wrong.
No. Learn measures the ratio from the engine speed and the road speed, so a road speed is needed. Type the ratios in from the gearbox's data instead.
Contact customer support at [email protected].
Related pages: Boost control · Traction control · Trigger inputs · ZF 8HP over CAN