Lift off the throttle on a turbocharged engine and the turbo starts to slow down at once: the exhaust that drives it all but stops. When you get back on the throttle, a second or more goes by before the boost returns. On a rally stage, a race track or a drag strip that lag costs time at every corner and every gear change. An anti-lag system keeps the turbo spinning while the throttle is closed, so the boost is there the moment you need it.
The RM-Primis anti-lag works with ignition retard, extra fuel, a spark cut and an air valve. This page explains how it works, how to set it up and how to tune it without destroying the turbo.
Anti-lag burns fuel in the exhaust manifold and the turbine housing. It makes extreme heat and loud bangs, and it shortens the life of the turbo, the manifold, the exhaust valves and the catalyst. Use it in motorsport only, with short Time active values, and never on the road.
When the driver lifts, the ECU does four things together for Time active:
The energy released in the exhaust keeps the turbine turning and the boost up, even with the throttle shut. To hold boost through the lift, the boost control has to keep the wastegate closed too: set the closed-throttle row of the boost target table to the boost you want (or, in open loop, a high duty).
When it starts. Anti-lag is armed when the throttle goes to or above the TPS threshold, and it starts when the throttle then falls 5 points below it (from 30 % to 25 %, for example), provided that at that moment:
Once started it runs for Time active, even if the throttle opens again.
Open Tune → Motorsport → Antilag (see the menu on the Launch control page). The page shows the three anti-lag tables, the Antilag settings below them and the live values beside them.
The tables are read by engine speed across and throttle position down. Anti-lag runs with the throttle almost closed, so the throttle axis covers only the first few percent: 0.1 % (fully closed) to 10 %.
The timing while anti-lag is active, in degrees. Negative values are after top dead centre: -20° fires the spark 20° after TDC.
The example above runs 0 to 5° with the throttle slightly open and -15 to -25° with it closed, where the turbo most needs the heat. Keep the result within ±59.9°.
The fuel added while anti-lag is active, in %: 10 adds 10 %, -5 takes 5 % away. The lambda target moves with it and closed-loop lambda correction pauses. With Incorporate in fuel math on the lambda table, the richer target adds fuel of its own, so the change counts about twice.
The share of sparks cut while anti-lag is active: 20 % cuts one spark in five. The cut also keeps the engine speed under control with the air valve open. Above the rev limiter's soft limit, the larger of this and the rev limiter's own cut is used.
The table tools are described on the Fuel table page.
| Setting | What it does |
|---|---|
| Enable Antilag | Switches anti-lag on |
| External valve | On: anti-lag drives its own air valve on Valve output 0-100% and leaves the idle valve alone. Off: it opens the idle valve, which needs idle control enabled |
| PWM frequency | The external valve's drive frequency. It takes effect the next time the ignition is switched on |
| Valve output 0-100% | The output that drives the external valve: Active value while anti-lag is active, off otherwise |
| Invert valve output | Reverses the external valve's duty |
| Active value | The air opening while anti-lag is active: the idle valve's or the external valve's duty. It replaces the idle output outright, beyond the idle limits; when anti-lag ends the idle valve returns to its idle position |
| Table value is absolute | On: the ignition table is the timing. Off: it is added to the calculated timing |
| Clutch activation | On: the clutch input must also be active at the moment of the lift. On a car that does not use launch control or flat shift, a switch wired as the clutch input can then work as an anti-lag arming switch |
| Engine speed | Anti-lag starts only if the engine is at or above this when the throttle is lifted |
| TPS | Anti-lag is armed at or above this throttle and starts when the throttle falls 5 points below it |
| CLT | Anti-lag starts only if the coolant is at or above this |
| Time active | How long anti-lag runs after it starts. Short times limit the heat: a few seconds is usual |
The Live values panel shows the engine speed, the coolant temperature, the retard and the fuel change being applied, the clutch and whether anti-lag is active now.
| What happens | What to change |
|---|---|
| The boost still falls away on the lift | More retard; more fuel; check the boost table's closed-throttle row keeps the wastegate shut |
| The engine speed rises on the lift | Less Active value, more cut |
| The engine speed drops and the engine stumbles | More Active value, less cut |
| The lambda goes very lean during anti-lag | More fuel in the anti-lag fuel table |
| Black smoke and soot, boost no better | Less fuel |
| Anti-lag does not start | The throttle must first reach TPS, then fall 5 points below it; check Engine speed, CLT and Clutch activation |
| Exhaust temperature far too high | Shorter Time active, less retard; use anti-lag only where it matters |
It shortens its life. Anti-lag puts combustion heat and pressure pulses straight onto the turbine wheel. Motorsport teams accept that for the lost lag; on a road car the cost is rarely worth it. Keep Time active short and the retard no greater than you need.
Yes. With External valve off, anti-lag opens the idle valve to Active value. Idle control must be enabled. Engines with a small idle valve may need a larger external valve for strong anti-lag.
Launch control builds boost with the car standing still and the clutch pressed. Anti-lag keeps the boost up while the car is moving and the driver lifts off the throttle, at corners and between gears. They use similar tools (retard, fuel and a spark cut), and they can be used together. See Launch control and flat shift.
Yes, on a car that does not use launch control or flat shift: wire a switch as the clutch input and turn Clutch activation on. Anti-lag then only starts while the switch is on. (Launch control and flat shift use the same input, so they would see the switch as the clutch.)
Contact customer support at [email protected].
Related pages: Boost control · Idle control · Launch control and flat shift · Rev limiter