In a modern car the engine computer is one voice among many on the CAN bus: the instrument cluster expects the engine speed and temperature from it, the ABS and the gearbox expect torque figures, and an aftermarket dash or logger wants everything. The RM-Primis speaks on the CAN bus in three ways: it broadcasts the donor car's original engine messages so the factory cluster and modules keep working, it sends its own data to aftermarket dashes and loggers, and it listens to the gearbox, the ABS, wideband controllers, EGT modules and buttons.
This page covers the CAN bus settings that tie it all together: bus speed and termination, the OEM chassis broadcast, the gearbox, OBD-II and the CAN analyser.
Open Setup → CAN bus:
| Page | What it holds |
|---|---|
| EGT over CAN | Sets up an RM EGT module and hands its channels to the ECU |
| Settings | Bus speed, termination, receive addresses, OEM broadcast, gearbox and shifter (this page) |
| Input settings / Input values | Reading values from other devices: see CAN inputs |
| Broadcast | The RM-Primis data stream for dashes and loggers: see CAN bus protocol |
| Analyser | Every CAN message the ECU sees, live |
| SMG settings / 8HP settings | Gearbox pages, shown when that gearbox is selected |
| Setting | What it does |
|---|---|
| Speed | The bus speed: 62.5 kbps to 1 Mbps. Every device on the bus must use the same speed. Most cars and dashes use 500 kbps |
| Resistor | Switches on the ECU's 120 Ω termination resistor |
| ODB-II addr. | The address the ECU answers OBD-II requests on (0x7E8 by default), for scan tools and OBD-II gauges |
A CAN bus needs exactly two 120 Ω termination resistors, one at each end. If the RM-Primis is at one end of the bus, switch its Resistor on; if the car's own modules already terminate both ends, leave it off. With the power off, the resistance between CAN high and CAN low should read about 60 Ω.
Up to 16 addresses (message IDs) the ECU listens to, chosen with Input number, used by the CAN inputs:
| Setting | What it does |
|---|---|
| Enable | Switches this address on |
| Extended CAN ID | For 29-bit identifiers instead of the standard 11-bit ones |
| CAN ID | The message ID to listen to |
| Poll | For devices that only answer once asked: the ECU sends a request at Frequency |
| Timeout | The time allowed for a polled device to answer |
| EGT | Opens the EGT module tool |
Broadcast makes the RM-Primis send the original engine computer's messages of the donor car, so the instrument cluster, the ABS/DSC, the gearbox and other modules keep working: rev counter, temperature gauge, warning lamps, torque figures. Choose the car the engine and the cluster come from:
| Broadcast | For |
|---|---|
| BMW E36-E46 (M3) | BMW E36 and E46, including the M3 |
| BMW E39-E53 (M5) | BMW E39 and E53 |
| BMW E6x/8x/9x | BMW E60, E8x and E9x series |
| BMW Fxx series | BMW F-series |
| VAG pre PQ35 / VAG PQ35 | VW and Audi platforms |
| Volvo P2x | Volvo P2 platform |
| Fiat, Ford, Mazda RX8, C180 | Those platforms |
| Haltech, AiM | Dashes that expect those protocols |
Platforms marked * in RM-Tuner have had limited testing: check every gauge and lamp works before you rely on them.
| Setting | What it does |
|---|---|
| Automatic transmission selection: Model | The gearbox on the CAN bus: BMW E36/E46 automatic, DSG, BMW 8HP or BMW E46 SMG. The ECU then exchanges the torque and shift information that gearbox needs |
| 8HP shifter: Shifter Type | For the ZF 8HP: a BMW F-Series shifter, or a Sequential or Dodge shifter in emulation |
| 8HP shifter: Paddles | The paddles: BMW (OEM Protocol) or Sequential (emulation) |
See ZF 8HP over CAN, Paddle shifters and BMW SMG.
Setup → CAN bus → Analyser lists every message the ECU sees on the bus, live: its identifier and its data. Type an identifier in Watch to follow just that message; Show all goes back to everything. Start log records the traffic to a file and Export table saves the list.
Use it to check a device is really on the bus before setting up a CAN input, to find which message carries a value, or to confirm the ECU is receiving the gearbox and ABS.
EGT over CAN opens the tool for RM's EGT module: read and write its settings, its CAN speed and the addresses of thermocouples 1–4 and 5–8, its scaling, and update its firmware. Use on ECU sets up the ECU's CAN inputs for the module's channels, so the exhaust temperatures appear in the live data and the logs without setting each input by hand.
Choose the donor car under Broadcast, check the bus Speed and the wiring, and look in the Analyser for the cluster's own messages, which prove the wiring is right.
Only if the RM-Primis is at one end of the bus. A correctly terminated bus measures about 60 Ω between CAN high and CAN low with the power off; 120 Ω means one resistor is missing, 40 Ω means one too many.
Yes: it answers OBD-II requests on the address set in ODB-II addr.
Contact customer support at [email protected].
Related pages: CAN bus protocol · CAN inputs · ZF 8HP over CAN · BMW SMG · Round CAN gauge