A high-power engine needs huge injectors at full load, but huge injectors idle badly: their pulses at idle are so short that the fuel delivered becomes hard to control. Staged injection solves it with two sets of injectors. A small primary set does all the work at idle and cruise; a secondary set, often in the intake plenum or a second rail, joins in as the load rises. The engine gets the fine control of small injectors and the flow of big ones.
This page explains how the RM-Primis shares the fuel between the two sets, how to set it up and how to tune the hand-over.
The ECU works out the total fuel the engine needs as usual. The Secondary split table then decides how much of it the secondary injectors deliver, in %, by engine speed and load; the primaries deliver the rest. Because the ECU knows the flow of the secondary injectors, it converts their share into the right pulse for them.
| Mode | When the split table is used |
|---|---|
| Table % | All the time: the split is whatever the table says at that speed and load |
| Split above duty | Only once the primary injectors reach their duty limit: below it the primaries do everything |
Minimum linear pulse. If the secondary share would give the secondaries a pulse shorter than this, the ECU keeps that fuel on the primaries instead, so the secondaries never work in their unpredictable small-pulse zone.
Injection angle offset. The crank angle between the primary and the secondary pulse, so the two sets can fire at different points in the cycle.
Switch on Staged injection on Fuelling settings. The Staging, Staging table and Staged injector dead time pages then appear under Tune → Fuel → Fuelling settings.
| Setting | What it does |
|---|---|
| Enabled | Switches the secondary injectors on |
| Injection Angle Offset | The crank angle between the primary and the secondary pulse |
| Injector flow (cc/min) | The flow of one secondary injector at its rated pressure |
| Minimum linear pulse | The shortest pulse the secondaries deliver reliably, dead time excluded. Below it the fuel stays on the primaries |
| Number of injectors | How many injectors are in the secondary set |
| Split above duty / Table % | When the split table is used: only once the primaries reach their duty limit, or all the time |
| Injector outputs | The outputs that drive the secondary injectors: spare injector outputs, or the general purpose outputs 4 and 5 |
A general purpose output used for injectors must not be used for anything else, and must be able to drive the injectors' current. Check the wiring diagram before using one.
The share of the fuel the secondaries deliver, by engine speed and load. In the example the primaries do everything up to atmospheric pressure, the secondaries start to help at 130 kPa, and at full boost and high speed they deliver 60 %.
How to shape it. Bring the secondaries in gradually: a smooth ramp over two or three load rows hides any small error in the secondary flow or dead time, where a sudden step from 0 to 50 % would show it as a lean or rich jump. Keep the primaries' duty below about 80–85 % everywhere.
The dead time of the secondary injectors by battery voltage, set exactly as the primaries' on Injector dead time, with its own Quick cal. Get it right before tuning the split: a wrong secondary dead time makes the mixture change as the split changes.
| What happens | What to change |
|---|---|
| The mixture goes lean as the secondaries come in | The secondary flow is set too high, or their dead time too short |
| The mixture goes rich as the secondaries come in | The secondary flow is set too low, or their dead time too long |
| A stumble right at the hand-over | Ramp the split in more gently; check Minimum linear pulse |
Control at idle and light load. Big injectors run very short pulses at idle, where they are least predictable. With staging, the small primaries handle idle and cruise and the big secondaries only add fuel at high load.
Yes: in the plenum, in the intake runners further from the valve, or in a second rail. Use the split table and the injection angle offset to suit them.
Contact customer support at [email protected].
Related pages: Fuelling settings · Injector dead time · Small pulse width compensation · Fuel table